Skip to main content

Error 0x61011beb, 0x61011bec, 0x610000f6, 0x61000f6 on HP Officejet and Photosmart printers

Error 0x61011beb, 0x61011bec, 0x610000f6, 0x61000f6 on HP Officejet and Photosmart printers
MAJ 27/05/17

Ox61011beb, 0x61011beb, 0x61011bec, 0x610000f6, 0x61000f6, Ox61011bed, 0x61011bed, 0x61000032, 06x610000f

These error code could appears on these printers:
  • HP Photosmart D5460, D5463, et D5468, C390A
  • HP Officejet 6000 6500 6500A 7000 7110

Solution 1:
  • With the printer power on, disconnect the USB cable from the computer.
  • Remove the ink cartridges
  • Unplug the power cord. Wait for at least 1 minute. Plug the unit back in (press the power button if necessary)
  • Wait for the "Insert Cartridges" message. Reinstall the cartridges
    Close the product doors
  • If you receive a recalibration message, allow the printer to complete this task
  • Reconnect the USB cable
  • Try your print job again

Solution 2:
  • Plug it directly into the wall, rather than into a UPS.
  • Verify that the unit is switched on. Disconnect the USB/Ethernet cable from the All-in-One and also disconnect power cable from All-in-One and also from wall outlet.
  • Wait 30 seconds.
  • Plug in the power cable to All-in-One and also to wall outlet.
  • Check for the functionality.


Solution 3:
  • Unplug the power cable from printer when the printer is powered on and wait for 20 seconds.
  • Then, press and hold # and 6 while plugging in the power cord.
  • Continue holding until it displays Semi Full Reset message in the front panel of the All-in-One
Solution 4:
  • Power off
  • Unplug the power cable from the wall outlet (should always power off first using the power button).
  • Remove the back piece and putting it back, making sure it's well adjusted.
  • Removed the piece where the printed paper land, and putting bac.

 Solution 5: fixing carriage jam on HP Officejet 6500 




Solution 6:

Solution 7: (Thanks to Justin !)
  • You need to replace the Clutch Drive Gear Kit (Ebay)

Comments

Anonymous said…
hp technical support sucks
Kit Eakle said…
What kind of nonsense is this??? After describing in 3 previous "solutions" how one should disconnect the poer WITHOUT powering down, HP asks in the 4th that you ALWAYS power down with the on off button first. Tried all "solutions" EXCEPT the last the 'print head costs almost as much as the printer! Shame!
Anonymous said…
forget HP
Anonymous said…
Didn't work on my printer, cartridge still won't go
Anonymous said…
SUCH BULL. THEIR SOLUTIONS SELDOM WORK. I AM DITCHING MY HP OFFICEJET 6500 AND BUYING AN EPSON. THEY ARE TRUSTWORTHY.
Anonymous said…
Well, this did not work at all.
Anonymous said…
None of these "solutions" worked. Don't waste your time.
Mary said…
I fixed mine by one of two ways- not sure which. Tried everything as far as post and also cleaned roller heads too. It looks like the roller heads that drop down and spin against the paper are too slick because they are plastic instead of rubber and were not making good contact with the paper. I decided to fill it full of paper to insure better contact. I also put in paper from Office Depot that is labeled "Colorlok" Technology and it worked fine. I think it was the type of copy paper I was using that caused the problem. It could have been as simple that I didn't load enough copy paper when I filled it too
Martin said…
Provided solutions do not work for my printer. Think i have a minor problem but do not know how to fix it. Neither does HP.
Anonymous said…
uselessssss... I'm going to buy another printer and will make sure it is not a HP
Anonymous said…
My cartridge rolls smoothly across left and right, then gets stuck in right hand side.

I've followed the HP guides and I've checked every nook and cranny and no obvious issue.

But the fact that it moves smoothly then locks in one spot really irritates me.
J.Lassalle said…
Hi,
Have you tried to put manually and gently the cartridge rolls to the center ?
Unknown said…
i bought 4 printer for my office .
now all have same problem after 1 year and here in saudi arabia no one have any idea what to do . they say buy new one .
Anonymous said…
HP!!!!! Your technical support sucks, you are not just wasting your money but our money and time with your lousy products. After my experience with 6500A, I can only advice consumers to stay away from HP...its not reliable....
domkasanova said…
I was trying all this solutions and nothing of your solutions can work ...
Anonymous said…
None of these solutions work. It is a piece of junk. I am buying a different brand.
Anonymous said…
IF ALL OF THE OTHER "FIXES" DON'T WORK, TRY CLEANING THE DECODER STRIP. IF IT IS DIRTY IT WILL CAUSE THE ERROR. The decoder strip is the the long white plastic strip inside that the carriage runs across. Just open the door, look inside to the back of the cavity and you will see it. To clean, simply moisten a bit of soft cloth and use it to gently wipe the strip clean as much as possible. Be warned, in all likelihood, you will get some ink on your hands. It washes off with soap and water. Have it ready. I have had this fix a number of printers including a HP 6700 that I just "repaired" after trying the normal fixes that did not work.
Anonymous said…
I tried all of the solutions recommended. Nothing worked. I keep getting the error message.
J.Lassalle said…
Hi,

If you still have the error message after changing the printhead, then the mainboard is defective.
Unknown said…
None of the above works
Tujo said…
HP only want money... they don t care about their users... shame on you HP. our solutions don t result... HP just want that we buy new printers... Im furious...
Joydd Mateus said…
Desisto. Mesmo com 4 indicações e mais algumas que andam por aí consigo. Desisto, desisto.
Unknown said…
http://www.ebay.com/itm/Clutch-Drive-Gear-Kit-for-HP-OfficeJet-6000-6500-6500A-7000-7110-Printer-Parts-/182066425074?hash=item2a64012cf2:g:JW8AAOSwr7ZW650o you're welcome

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr