Fix your printer !

You can have error E350, E-350 or E350-001 on these copiers: Canon IR105, IR6020i, IR6000, IR5020, IR2200, etc... E350 means there are faults on serial number (SN) PCB. A check is made at power-on Solution : Turn off the machine's main power switch. Replace the serial number PCB with a new one. Assemble the parts. Turn on the main power switch. One again, turn off and on the main power switch. Verify that the readings of the soft counters have been continued

You can have error code E000732-0001 on these Canon copiers: canon imageRunner 3200n, IR 3180, IR 7095, IR C2620, IR 5185n, IR 5570, IRC5185i, IR C3200, etc... Solution 1 : Check all the cables outside of the printer: they must be plugged, especially between the differents elements of the copier:  Solution 2 : Check all the connectors on the main board. Solution 3 : Unplugg and replugg all the leads between the boards and modules

Error code E315 means any of the following is true in the image processing by the main controller: 1. The image data has a fault. 2. The encoding/decoding operation for image data has a fault. 3. The image processing element of the main controller PCB has a fault. The image data, the main controller or the HDD is faulty. What to do: If this error occurs during normal copying or printing, the job in question (image data) is cleared when the main power switch is turned off and then on again. If this error occurs frequently, however, a fault on the main controller PCB is a possibility. If this error occurs in a specific image within the Mail Box, damage in data may be assumed: be sure to delete the image from the Mail Box.

E719 :  The communication between the card reader and the image processor PCB is disrupted. Possible cause The wiring is faulty (short circuit, open circuit). The card reader is faulty. The image processor PCB is faulty. To clear the error in service mode : #12 CLEAR-CARD. Solution: 1) Connector: Is the connection and the wiring for the connector (J1131) of the card reader and the connector (J210) on the image processor PCB normal? 2) Image processor PCB: Try replacing the card reader. If the fault not corrected: replace the image processor PCB. --- E805 After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time. Possible cause The fan wiring is faulty (short circuit, open circuit). The heat discharge fan (FM101) is fautly. The DC controller PCB is faulty. Solution: 1) Remove the foreign matter on the fan. 2) Wiring, Connector: Is the connection and wiring of the connector (J951) of the heat di...

  E000 : The main thermistor reading does not reach 40ºC 14 sec after the fixing heater goes ON. (fixing low temperature error) E001 : The main thermistor reading reaches 220ºC or higher. E002 : A start-up fault is detected under any of the following conditions of the main thermistor E003 : After the end of the WAIT period, the main thermistor reading is 100ºC or lower. In standby, the sub thermistor reading is 50ºC or lower. E004 : At time of initialization, the ZEROXI signal of the power supply is not detected. During temperature control, the ZEROXI signal does not arrive for 3 sec continuously. A short circuit is detected in the triac E010 : A specific revolution is not detected from the main motor rotation detection signal. E100 : When the scanner motor is started up, the BD input signal does not arrive within a specific period of time. When the scanner motor is started up, the motor rotation is too fast, and fails to reach a specific revolution within 20 sec at time ...

E733-0001 means a fault is detected by the main controller PCB in the communication between the DC controller PCB and the main controller PCB. Main cause: The connector has poor connection. The DC controller PCB is faulty. Solution : Verify the connection between the connector J1015 on the main controller PCB and the conductor J316 on the DC controlled PCB is normal. Correct the connection if necessary. The connection is correct: Replace the DC controller PCB .