Fix your printer !

The message " Power Off/On 929:error " means there is an error from the waste toner transfer motor lock. This message appears on these models: Oki C9650, C9650dn, C9650hdn, C9650hdtn, C9650n, C9850, C9850n, C9850dn, C9850hdn, C9850hdtn, Xerox Phaser 7400DN 7400DNZ 7400NZ 7400VN 7400VDN 7400VDT 7400VDX 7400VDXE. Solution 1 : Reinstall the waste toner transfer Solution 2: Replace the waste toner motor

The message "Service Call 196: error" is an error from the upper side thermistor. Solution 1 : Power off and on the printer Solution 2 : Power off Umplug the power cable Wait ten minutes Plug in the power cable Power on the printer

MAJ 27/07/15 Here is two procedures to reset the drum counter on OKI C5650 : Solution 1 : Turn the machine on while pushing and holding "Up" and "Down button at same time. Menu window will show "Oki User" Scroll to " Engine DialogMode" and push Enter button. "Diagnostic Mode xx.xx.xx S-Mode" is indicated. Scroll to "NV-Ram initial"  and push ENTER. Screen shows "NV-Ram- Initial Table 1". Push "Online" and "Enter" Buttons simultaneously and Hold for 10 seconds after you see "Executing Reset" in menu window. Restart printer. Solution 2 (if solution 1 does not work): Replace the chip on the drum :

Solution to reset to the default settings : Enter in "Maintenance Menu" Go to "Execute. If you want to reset the drum counter: The reset is automatic when you insert the new drum. If not: reinstall the drum.

Downloads : Drivers and manuals Cartridges: 42918904: Toner Black C7 42918903 : Toner Cyan C7 42918902 : Toner Magenta C7 42918901 : Toner Yellow C7 42918104 : Image drum Black C7 42918103 : Image drum Cyan C7 42918102 : Image drum Magenta C7 42918101 : Image drum Yellow C7 Parts: 42931701 : Fuser 120V 42931702 : Fuser 230V 42931602 : Transfer Belt 42937601 : Finisher Staples 42869401 : Waste toner collection bottle Troubleshooting: Drum reset: Solution 1: Switch off the power to the printer. Wait approximately five seconds and then flip the power switch back on. Press and hold the "Menu 1/Menu2" button on the control panel and press the "Shut Down/Restart" button to restart the printer. Press the "Menu1/Menu2" button three times in succession until "DRUM CNT RESET" appears on the control panel. Press the "Enter" button to reset the image drum counter on the C9600 printer. Solution 2:

MAJ 04/04/16 Downloads : Drivers Utilities  Users' Guide Accessory Instruction Guide Consumables : Okidata Brand C5500n High Yield Black Toner - 43324404 Okidata 43324401 High-Yield Laser Printer Toner 5000 Page-Yield Yellow Okidata 43324402 High-Yield Laser Printer Toner Type C8 5000 Page-Yield Magenta Okidata 43324403 High Capacity Cyan Toner Cartridge Okidata C5500, C5650, C5800 Series Black Drum (20,000 Yield), Part Number 43381704 Okidata  43381701 Drum unit Yellow For C5650N (Drum/Drum Kit) Okidata C5500, C5650, C5800 Series Magenta Drum (20,000 Yield), Part Number 43381702 Okidata C5500, C5650, C5800 Series Cyan Drum (20,000 Yield), Part Number 43381703 Okidata C5650 Series Transfer Belt Popular High Quality Practical Modern Design Troubleshooting : Fatal error code 173: This error indicates that the Image Drum Up/Down Process is not working properly. The errors are as follows: 140 - Yellow Drum Up/Down error 141 - Magenta Drum U...

After replacing your Toner or Drum you get this message: “Toner Sensor Error”. This error appears on these printers: C3200n, C3520, C9200... Solution : Possible Cause #1 : Toner cartridge may not be locked into the Drum properly or the Toner/Drum unit may not be locked into the printer correctly. Resolution: Check the Toner cartridge Lock Lever (Figure 1) and make sure it is in the LOCKED position: Possible Cause #2 : Error may occur if the plastic Shutter / Flap on the side of the Toner cartridge is fully or partially down blocking the Toner Sensor window (C3000 Series printers). Resolution: Move the Flap upward and out of the opening to allow for the Toner Sensor to become fully exposed prior to reinstalling the Toner and Drum combination. This is a simple, easy step you can perform. (Ref. Figure 2) The safest way to move this shutter is either with a toothpick or something plastic. Do NOT use a paper clip or anything metal to move the shutter. A metal object may ...

Solution : Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed. Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed. Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed. Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables. Press either the + or – buttons to scroll through the various consumables, at the desired consumable press the Enter button and the last digit of the count will start flashing. Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count. Once the count is at the level you desire, press and hold the On-line, Cancel, & Back buttons simultaneously until the ...