Fix your printer !

Error 11:10 on HP Designjet means that the trailing cable is not detected. Solution 1 : Turn off the printer Disconnect the power cord. Wait five minutes Reconnect the power cord, and turn on the printer. Solution 2 : Check that the trailing cable is correctly connected between the engine PCA and carriage PCA. Solution 3 : Check that the trailing cable connectors are not damaged, especially on the E-Box side. Rreplace the trailing cable if necessary. Solution 4 : Check that the power cable from the power supply unit is connected to the formatter.

Error code 010030 034c095e means that the power supply detects a low spike. Solution 1 : Power off the printer Disconnect the power cable Wait 5 minutes Reconnect the power cable et switch on the printer Solution 2 : Try to plug the power cable in another outlet Solution 3 : In some case, it could be a defective lifter drive motor. You have to replace this part: RG5-6665-000

System Error: 08:YZ Problem Description: Problem with the Front Panel . Corrective Action: Solution 1 : Switch off the printer Wait 5 minutes Switch on. Solution 2 : Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. Check that the Front Panel interface cable is not damaged and is correctly connected between the Main PCA and the Front Panel. Check that the memory module in the Formatter is installed correctly. Check that the connections between the Formatter, the Formatter and the Formatter are not damaged and are correctly connected. Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. If the System Error continues, replace the Main PCA If the System Error continues, replace the Formatter  If the System Error continues, replace the Front Panel Parts : T610/T1100 formatter board: Q6683-67030 T610/T1100 ...

Solution : You have to connect the trailing cable at two ends. One in the back and one to the printhead.  Before reconnecting, check the ends on the cable as sometimes the connection points get bent or damaged.  If that does not solve your issue: replace the cable ( C7769-60305 or C7770-60274 )

Problem description for " System Error: 86:01, 0X8010003 ": That is a Carriage-Axis shutdown. Solution 1 : If this error code appeared but was not caused by a paper jam, then try the following: Enter the Printer Information and check the Scan-Axis usage.  If the percentage is close to 100%, then lubricate the Slider Rod (there is probably too much friction in the Slider Rod). Solution 2 : The Carriage is bumping into the Service Station. If the carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen it is because the Service Station cannot uncap the Printheads.  Replace the Service Station. Solution 3 : Verify the Service Station Take out the service station and make sure it run through its full range of motion by rotating the motor spindle.  Check for the rods, that holds the cleaners, to be not popped out. If yes: place the rod back into its socket and reinstall it back into the syst...

SYSTEM ERROR 010060 is a Primer Motor sensor problem. Sensor might be bad, motor might not be turning, cable could have failed, or main PCA might be bad. Some parts for HP Designjet 750c: C3146A: 16MB for HP Color Laserjet (c3100a)   C4706-60082: HP Designjet 430, 450C, 455CA, 488CM belt for 36" print width plotters   C4705-60082: HP Designjet 430, 450C Belt for 24" print width printers

Remove the left hand cover: Switch off the Printer and remove the power cable. 1. Remove ALL the Ink Cartridges from the Printer. 2. Open the Top Cover. 3. Open the door at the back of the Left Hand Cover. 4. Disconnect the Electrical Cable from the rear of the Ink Cartridge Tube Connector. 5. Disconnect the Air Tube. 6. Twist the 3 latches at the rear of the Ink Cartridge Tube Connector and release the complete Assembly. 7. Remove the Ink Cartridge Tube Connector and place safely on the window. 8. Remove 1 T-15 screw (Type F) from the Left Hand Cover (rear). 9. Close the Left Back door and remove 1 T- 25 screw (Type U) from bottom side (rear) of Left Hand Cover. 10. Remove 3 T-15 screws (Type F) from the Left Hand Cover (front). 11. Remove the Left Hand Cover from the Printer. When handling the Tubes make sure you do not damage them by twisting. Remove the right rear cover: 1. Remove one T-15 screw (Type B) from the Right Rear Cover. 2. Remove the Right Rear...