Skip to main content

Printer Canon Pixma IP6600D

MAJ 13/11/15
Downloads:

Cartridges:

Parts:

Troubleshooting:
  • Error 5200: printhead temperature rise error
Power off the printer.
Wait 5 minutes and power on.
If the error persist, the printhead must be replaced.
  • Error 6500: hardware error; it could be:
- The chip of a cartridge is positioned incorrectly and is not recognized by the printer at once.
- Electronic board is faulty.
  • Error ink cartridges are not installed properly (Error E5)

Unplug power and USB cable.
Open door and hold power button.
Connect power.
Close door, then release power button.
  • How to Reset waste ink counter: 

Power off the printer.
While holding STOP/RESET button, power on the printer.
While holding POWER button, release STOP/RESET button.
Push STOP/RESET button twice and release the two buttons.
Wait about 20-30 second until the LED shows “0″.
Push STOP/RESET button four times.
Push POWER button twice.


Comments

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Service tool V3400 for resetting Canon printers counter

MAJ13/02/18
The Service Tool V3400, and service tool V3600, allow you to reset the waste ink pad counter on some Canon printers: 

You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers:
Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240 Canon MX397, MX320, MX330, MX370, MX860 etc
Where can you download the Service Tool V3400 ?

It is free here:
https://1fichier.com/?c198556kp0
There is too a paid version here:
V3400 Canon Service Tool for all iPxxxx series, i…

How to fix error 6C10 on Canon Printers

MAJ 21/12/14
Error 6C10 appears on these Canon printers: MP110,MP550, MP560, MP540, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MP620, MP640, IP3600, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200... and others...
It's a "valv cam sensor error".


Solution 1:
Move the printhead to the center.Disconnect the printer and check on the right: is the purge unit ok ? No peace of paper ?
Solution 2:
Do a reset of the printer:Power onHold down the "Resume" button (triangle in a circle)  for 15 to 20 seconds.
Solution 3:
Power off the printer.Open the door.Power on.When the cartridge is in the center, close the door.
Solution 4:
Open the lid and allow the ink cartridge carrier to center itself. Looking to the right, you will see a row of white rollers behind the carrier. At the end of the rollers there is a small, clear piece of plastic that sticks up. Take a small piece of a paper towel and wipe all of the ink off this piece of plastic. When that is clean …