Skip to main content

Posts

Showing posts from 2011

Message "096: Fatal Error 02" with Oki printers

096-02 error is a problem with the finisher. That's a "tray raise or lowering error". Solution 1: Check and clean the upper limit switch.  Solution 2: Replace the upper limet switch Solution 3: Check the shift motor operation and finisher control PCB board.  If the motor has failed, you need to replace it, and perhaps the control PCB too.

Error message Service Req E020 on Epson printers

This error could appears on these models: EPL-N3000, Aculaser C1100, Aculaser C1900... Solution 1 : “Secondary transfer voltage contact/release problem” Some electric parts can cause the trouble:  Transfer Roller Pressure Solenoid (SL2)  Transfer Roller Pressure Position Detection Sensor (PC7)  Engine Board (PWB-A)   Solution 2 : The problem come from the fuser. You have to replace it. EPL-N3000: C13S053017BA  Aculaser  C1100: 2090471 Aculaser C1900: 2077368

Error 61.05 on HP Designjet 500, 510, 800

Could appears on HP DesignJets 800 Series, DesignJet 500 and 510. Printer show a System Error: 61:05 The problem : That's an error Processing Job. This Error Code appears in these HP DesignJets with an HPGL/ 2 card installed, when processing either a PostScript or HP-GL/2 file. Solution 1 : Switch the Printer Off  Wait a few minutes.  Switch the Printer On  Resend the file that you were trying to print.  Solution 2 : If the Error Code reappears, try to generate the file again and try to print again.  If the file that is causing this error is PostScript, check if it is Binary. If the file is Binary, use AppleTalk to send the file to the Printer.  If AppleTalk is not being used to send the Binary file to the Printer, you have to change the PostScript settings to Binary through the Front Panel (Set-up menu / PS settings / Encoding / Binary).  Solution 3 : If the Error Code continues to reappear, check for a new release of the ...

How to reset drum counter on Oki B4400

Solution to reset the drum counter: Open the Status Monitor. Click "Printer Setup" then "Open Configuration" and "Maintenance". Click Drum Counter Reset. Click Apply. Click OK Réinitialiser le compteur du tambour Ouvir le Status Monitor. Cliquer sur "Printer Setup" puis "Open Configuration" et "Maintenance". Cliquer sur Drum Counter Reset (Réinitialiser le compteur du tambour). Cliquer Apply (appliquer). Cliquer sur OK Cero el contador del cilindro Abras Status Monitor. Clic en "Printer Setup" y "Open Configuration" y "Maintenance". Clic en Drum Counter Reset. Clic Apply (aplicar). Clic OK Reiniciar o contador do cilindro Lance o Status Monitor. Clique com "Printer Setup", "Open Configuration", "Maintenance". Clique com Drum Counter Reset. Clique Apply (aplicar). Clique OK Image Drum for Oki B4400 Printer

SSC Service Utility Software to reset Epson printers

SSC Service Utility allow to do many things with Epson printer : - Work directly with CSIC in Epson Stylus printers cartridges. - Reset or rewrite any chip using special addon device. - Freeze internal ink counters. - Reset internal ink counters even with empty cartridges. - Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode. - Hot swapping of cartridges supported. - Resetting of protection counter. - More then 100 different Epson printers supported The site: http://www.ssclg.com/epsone.shtml Download the 4.30 version Printers you can reset with SSC utility : Epson Stylus Сolor 400/440/480 LPT/480SXU/580/600/640/660/670/680/777/740/760/ 800/850/860/880/900 / EM-900C/980/1160/1520/3000 C20 / C40 / CL-750/C41 / C42 / C43 / C44 / C45 / C46 / C47 / C48/C50/C60/C61 C62 /C63 / C64 /C65 / C66/C67 / C68 / D68/C70/C80/C82/C83 / C84/C85 / C86/C87 C88 / D88 and PE Photo RX420 / RX425 / RX430 /RX500 / RX510/RX520/RX600...

Epson Stylus Photo R300 printer

Downloads : Drivers Manuals Cartridges : 7 Pack Compatible INK Cartridge for R300 Troubleshooting : Message on printer " some components have come to the end of their life ". You have to reset waste ink counter: Solution 1 : - Switch on the printer. - Hold on "STOP", "MAINTENANCE" and "POWER" buttons. - Release them when it's indicated. Solution 2 : Use the SSC Service Utility Software tou reset the product.

Brother MFC-425CN printer

Download : User's guide Cartridges : LC41BK: Black ink cartridge LC41C: Cyan ink cartridge   LC41M: Magenta ink cartridge   LC41Y: Yellow ink cartridge Brother Compatible LC41 8-Pack (2B/2C/2M/2Y) Troubleshooting: How to reset waste ink counter: Machine off Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode. press 80 press the “mono start” button several times until you see “purge: xxxx” press “2783” in order to reset the purge counter. You will see: “purge:0000” press “99” to exit the maintenance mode

How to solve error 16H on Konica 2300, 2300DL

Solution : Turn off the printer. Open the panel door exposing the toner waste container and cartridge access area. Gently pry away the waste toner container from the printer.  Put the waste toner powder into a garbage bag. There are two manual screws holding the transfer belt component securely. One is on the left upper part, one is on the right. They are designed to loosen, but stay attached to the transfer belt component. Flip the large blue handle with the arrow upward. Look for a portuding squarish handle below the larger blue handle transfer belt component. Look caredfully at the diagram on this little handle. You must squeeze the level on the underside of this squarish handle to unlock it. Once unlocked you carefully slide this part out. Put this whole component aside for later assembly back in. Carefully slide out the larger transfer belt component about 2/3 of the way out. You should see a pale green plastic handle on the top of this part. You can grab...

how to reset counter after tranfer belt and fuser replacement on clx2160n

Resetting the transfert belt's counter after replacement ( CLP-300 Imaging Kit ): Solution 1: Press: Menu, #1934, Menu, "Tech Mode " --> OK,  "Data Setup" --> OK, go to "Clear Counts" --> OK, "Enter Password [????]" --> 1934, OK, "Clear Counts [Total Page CNT]", go to "[Imaging Unit]" --> OK, "Clearing…", --> Back. Solution 2 : Enter Service mode by pressing: "menu", "id copy", "left", "right", "menu", "back", "menu" within 5 seconds. Then in data setup clear all memory and clear count Resetting the fuser's counter after replacement (JC96-03609A): Press: Menu, #1934, Menu, "Tech Mode" --> OK, "Data Setup" --> OK, go to "Clear Counts" --> OK, "Enter Password [????]" --> 1934, OK, "Clear Counts [Total Page CNT]", go to "[Fuser...

Samsung CLX 3175N, FN, FW Printer

Downloads : Manuals, drivers and software Cartridges : Toner Black CLX-3175   Toner Cyan CLX-3175   Toner Magenta CLX-3175   Toner Yellow CLX-3175 CLT-W409 waste bottle CLX-3175   CLT-R409: Imaging Drum For Samsung CLX-3175   ( Counter reset ) Parts : JC96-05491: Fusing Unit 0604-001095: Photo Interruptor Troubleshooting : Message " replace imaging unit ": You have to change the drum (CLT-R409) Message "System error cycle power": You have to change the photo interruptor.(0604-001095) How to unlock the scanner (message "Scanner locked"): Hold on " Stop " button during 10 seconds. How to replace the fuser unit

Canon Pixma MP530 printer

Download : Manuals Drivers and software Cartridges : Canon CLI-8 3 Pack C/M/Y Value Pack (0621B016) Canon CLI-8 4- Pack C/M/Y/BK Ink Tanks Canon CLI-8 8- Pack C/M/Y/BK Ink Tanks x 2   Canon PGI-5 Pigment Black Ink Tank Parts: QY6-0059 : Printhead Troubleshooting : Error 5B00 ; the waste ink counter need to be resetted: Turn off the printer Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green. Hold the Power Button, release the Resume Button. Not releasing the Power Button, double click “Resume” and release Both Buttons. Click “Resume” for Four times Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again. Error message U150

How to fix error code 0x61011be5 or ox61011be5 on HP printers

General Printer Error 0x61011be5. Appears on these printers: D7560, C309A, C5390, C6380, ... Genraly it's a carriage jam or a printhead issue. Solution 1 : Do a reset of the printer to factory default settings Verify that the unit is switched on.  Disconnect the  power cable from All-in-One and also from wall outlet. Wait a minute. Plug in the power cable to the printer and also to wall outlet. Unplug the power cable from the printer (with the printer powered on) and wait for 20 seconds. Then, press and hold "#" and "6" while plugging in the power cord. Release the buttons after connect power cord. Solution 2 : Open the printer and wait for the carriage to slide over Remove the ink cartridges from the print head. With a cotton swabs dipped in hot water, clean gently the print head and each ink cartridge, until there is no ink residue coming off on the cotton swab. Once all is dry, replace the cartridges Do a print test. If the er...

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges ...

Printhead for HP Officejet and Photosmart printers

HP Print Head Printhead CB326-30002 CN642A for HP 564XL and HP 564 : Hewlett-Packard OfficeJet 6000 Hewlett-Packard PhotoSmart B8500 Hewlett-Packard PhotoSmart B8550 Hewlett-Packard PhotoSmart B8553 Hewlett-Packard PhotoSmart B8558 Hewlett-Packard PhotoSmart C5300 Hewlett-Packard PhotoSmart C5324 Hewlett-Packard PhotoSmart C5370 Hewlett-Packard PhotoSmart C5373 Hewlett-Packard PhotoSmart C5380 Hewlett-Packard PhotoSmart C5383 Hewlett-Packard PhotoSmart C5388 Hewlett-Packard PhotoSmart C5390 Hewlett-Packard PhotoSmart C5393 Hewlett-Packard PhotoSmart C6300 Hewlett-Packard PhotoSmart C6324 Hewlett-Packard PhotoSmart C6340 Hewlett-Packard PhotoSmart C6350 Hewlett-Packard PhotoSmart C6375 Hewlett-Packard PhotoSmart C6380 Hewlett-Packard PhotoSmart C6383 Hewlett-Packard PhotoSmart C6388 Hewlett-Packard PhotoSmart D5400 Hewlett-Packard PhotoSmart D5445 Hewlett-Packard PhotoSmart D5460 Hewlett-Packard PhotoSmart D5463 Hewlett-Packard PhotoSmart D5468 Hewlett-P...

How to reset Waste ink Counter on Canon Pixma MP480 printer

MAJ 17/10/16 After a message error like " Ink Absorber is Full ", you need to reset the printer to solve the issue: Solution 1 : Search and download the resetter software Power cable and usb cable must be connected Enter in the Service Mode:  1. Turn off the printer without pulling the power cords. 2. Hold down STOP/RESET button and press Power button. 3. Keep holding down Power button and let STOP/RESET button go. 4. Then Press STOP/RESET button twice then let BOTH buttons go. 5. Alternate Blinking error is gone: your are in Service Mode state. Use the Resetter: 1. Extract the resetter software and double click "MP480.exe" W 2. Click Reload Button and you will get a new USB port. 3. Load some papers in your printer and press the "Main" Button once, 4. Wait until the printing is done. 5. Then press "EEPROM Clear" button to clear EEPROM. 6. Then press EEPROM button and the printer will print some text. 7. Then power...

How to solve error 5011 on Canon Printers

MAJ 02/01/15 Error 5011 is a scanner error . It occurs on these models: MP480, MP490, MX340, MX320, MX350, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100 Solution 1: Unplug power supply Wait 5 minutes Plug back in. Solution 1a (thanks to anonymous): Turn the printer off Open cover as if you want to change an ink cartridge. Turn power on and close cover while initializing   Solution 1b: Power off the printer Press and hold power+cancel simultaneously Hold on the power button and release cancel  Press cancel button 4 times, Release both. Solution 2 : Check for no pieces of paper, no littles objetcs inside the printer. Solution 3 : Carefully clean the encoder strip.  It's located behind the carriage that runs all the way from right to left Solution 4 : Replace the scanner unit

Reset transfert belt counter on Xerox Phaser 6110 MFP

Sometimes, when you have replaced the Image Transfer Belt, the printer still does not work. You will have to reset the counter. Procedure : Enter Service Mode by pressing [MENU] [#] [1] [9] [3] [4] quickly. Select Tech Menu Select DataSetup Arrow to Clear Counts and press Enter Enter Password 1934 Arrow to Transfer Belt and press Enter. The display will show Clearing Counts and then return you to the Tech Menu. Press exit several times to exit the Tech Menu and then power cycle the printer.

How to solve error 6A90 or "APP sensor error" on Canon printers

Error code 6A90 or "APP sensor error" occured during paper feeding or purging. Solution 1: check for foreign material or paper debris around the purge drive system unit; - remove foreign material. Solution 2: check for foreign material or paper debris around the ASF unit; - remove foreign material. Solution 3 : If other solution fail, replace one off the following part - Purge drive system unit - Logic board

Samsung ML 1610, 2010, 2015, 2510, 2571N fuse

Fuse is needed to reset the counter when a new cartridge is used This fuse is 250mAh and 3/4" inch long (20 mm) round glass with metal ends. It could be used with Samsung ML-1610 ML-2010 ML2010 ML-2015 ML2015 ML-2510 ML2510 ML-2571N ML2571N series For P/# ML-2010D3 and ML-1610D2 toner cartridge. Where to buy it: Amazon Ebay

HP Photosmart and Officejet Printhead

When you've tried all solutions for solving "0xc..." errors and any one works... you have to change the printhead. HP Print Head Printhead CB326-30002 CN642A for HP 564XL and HP 564 PhotoSmart B8500 PhotoSmart B8550 PhotoSmart B8553 PhotoSmart B8558 PhotoSmart C309 Series PhotoSmart C309a PhotoSmart C309g PhotoSmart C310a PhotoSmart C510a PhotoSmart C5300 PhotoSmart C5324 PhotoSmart C5370 PhotoSmart C5373 PhotoSmart C5380 PhotoSmart C5383 PhotoSmart C5388 PhotoSmart C5390 PhotoSmart C5393 PhotoSmart C6300 PhotoSmart C6324 PhotoSmart C6340 PhotoSmart C6350 PhotoSmart C6375 PhotoSmart C6380 PhotoSmart C6383 PhotoSmart C6388 PhotoSmart D5400 Series PhotoSmart D5445 PhotoSmart D5460 PhotoSmart D5463 PhotoSmart D5468 PhotoSmart D7500 Series PhotoSmart D7560 PhotoSmart eStation All-in-One PhotoSmart Fax e-All-in-One - C410a PhotoSmart Premium e-All-in-One PhotoSmart Premium Fax PhotoSmart Premium Fax All-in-One PhotoSmart TouchSmart ...

Canon Pixma IP2000 printer

Downloads :  Drivers, software and manuals Cartridges : Canon BCI-24 Black Inkjet Tank (6881A003) Canon BCI-24 Color Ink Tank Canon BCI-24 CLR, BLK and Glossy Photo Paper Combo Pack (6881A055) Parts: Canon printhead QY6-0054-000 Troubleshooting : Message error "waste ink tank full" . You have to reset it: Start with the power off. Hold down the "On/Off" button plus the "Resume" button at the same time without release them. Let go of the "Resume" button only. Then press the "Resume" button twice. Let go of the "On/Off" button. Press the "Resume" button 4 times Press the power button 2 times. The printer should now be okay and the lights will return to norma.

Unable to print 50 and unable to print 30 error messages on Brothers printers

Solutions for "Machine error 50" and "Machine error 30": Solution 1 : Lift the scanner cover using the plastic tabs, located on the left and right side of the machine until it locks securely into the open position. Slide the print head to the middle. Check for any pieces of paper or staple , paper clip... Solution 2: Lift the scanner cover using the plastic tabs, located on the left and right side of the machine until it locks securely into the open position. Slide the print head over to the right side under the cover to make sure you clean the entire encoder strip.   With the lint free cloth, firmly grab the encoder strip on both sides and rub the cloth down the strip from one end to the other (left to right then right to left) at least three times.   Solution 3: the encoder strip which gives the printhead the position is out of place. You have to open the printer and reinsert the strip: For MFC-845CW: 1) Lift cover. Remove ...

Oki C5650, C56250n, C5650dn Printer

MAJ 04/04/16 Downloads : Drivers Utilities  Users' Guide Accessory Instruction Guide Consumables : Okidata Brand C5500n High Yield Black Toner - 43324404 Okidata 43324401 High-Yield Laser Printer Toner 5000 Page-Yield Yellow Okidata 43324402 High-Yield Laser Printer Toner Type C8 5000 Page-Yield Magenta Okidata 43324403 High Capacity Cyan Toner Cartridge Okidata C5500, C5650, C5800 Series Black Drum (20,000 Yield), Part Number 43381704 Okidata  43381701 Drum unit Yellow For C5650N (Drum/Drum Kit) Okidata C5500, C5650, C5800 Series Magenta Drum (20,000 Yield), Part Number 43381702 Okidata C5500, C5650, C5800 Series Cyan Drum (20,000 Yield), Part Number 43381703 Okidata C5650 Series Transfer Belt Popular High Quality Practical Modern Design Troubleshooting : Fatal error code 173: This error indicates that the Image Drum Up/Down Process is not working properly. The errors are as follows: 140 - Yellow Drum Up/Down error 141 - Magenta Drum U...

Canon I80 printer

MAJ 04/04/16 Downloads : Drivers and software Manuals Cartridges : Canon BCI-15 Black Ink Cartridge (Twin Pack) Canon BCI-15 Twin Pack Color Ink Cartridges Parts : QY6-0052 Printhead i80, iP90, i90v Printers Universal Adapter for i80 Color Bubble Jet Printer BU-10 Bluetooth Adapter for i80 Printer Troubleshooting: : How to reset ink counter: - Close the print head cover, and turn off the printer. - Hold on "Resume/Cancel" button, press the "Power" button. - While holding the "Power" button, release the "Resume/Cancel" button. - While holding the "Power" button, press the "Resume/Cancel" button three times, and then release the buttons. - During initialization, the LED blinks in green. - When the LED stops blinking and lights in green, press the "Resume/Cancel" button the 4 times. - Press the "Power" button. The LED lights in green, and the selected function is...