Skip to main content

Brother MFC-425CN printer

Download:

Cartridges:



Troubleshooting:
  • How to reset waste ink counter:
Machine off
Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode.
press 80
press the “mono start” button several times until you see “purge: xxxx”
press “2783” in order to reset the purge counter. You will see: “purge:0000”
press “99” to exit the maintenance mode

Comments

Anonymous said…
worked for MFC420CN !
Anonymous said…
https://elektrotanya.com/brother_mfc620_420_410_210_fax2440_dcp310cn_110c_sm.pdf/download.html

is the service manual showing that instruction.
Anonymous said…
-2783 also zeros droplet counts: 14th item is DOT_ K: Total Counts and 15Th: SENS K: drops since near empty.
Fixes NO CARTRIDGE from INK EMPTY: BLACK and lotsa' ink.
That procedure is not in the Service Manual , but droplet counts are mentioned in the
troubleshooting as a cause of those messages .

Mode 11 prints 4 pages of mode 10 soft switch settings with descriptions; mode
82 prints the mode 80 MAINTENANCE log variables.

Setting WSW49 bit 8 of mode 10, prints black only; Adobe has grayscale option
Setting WSW31 bit 4 of mode 10, turns off cartridge sensors, and landscape ability
Printer stops when low ink and spits out partial page; next attempt will do
CLEANING first so be sure ink levels OK.

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges ...

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

Service tool V3400 for resetting Canon printers counter

MAJ13/02/18 The Service Tool V3400 , and service tool V3600 , allow you to reset the waste ink pad counter on some Canon printers:  You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 There is too a paid version here: V3400 C...