HP Photosmart and Officejet Printhead

When you've tried all solutions for solving "0xc..." errors and any one works... you have to change the printhead.

HP Print Head Printhead CB326-30002 CN642A for HP 564XL and HP 564

PhotoSmart B8500
PhotoSmart B8550
PhotoSmart B8553
PhotoSmart B8558
PhotoSmart C309 Series
PhotoSmart C309a
PhotoSmart C309g
PhotoSmart C310a
PhotoSmart C510a
PhotoSmart C5300
PhotoSmart C5324
PhotoSmart C5370
PhotoSmart C5373
PhotoSmart C5380
PhotoSmart C5383
PhotoSmart C5388
PhotoSmart C5390
PhotoSmart C5393
PhotoSmart C6300
PhotoSmart C6324
PhotoSmart C6340
PhotoSmart C6350
PhotoSmart C6375
PhotoSmart C6380
PhotoSmart C6383
PhotoSmart C6388
PhotoSmart D5400 Series
PhotoSmart D5445
PhotoSmart D5460
PhotoSmart D5463
PhotoSmart D5468
PhotoSmart D7500 Series
PhotoSmart D7560
PhotoSmart eStation All-in-One
PhotoSmart Fax e-All-in-One - C410a
PhotoSmart Premium e-All-in-One
PhotoSmart Premium Fax
PhotoSmart Premium Fax All-in-One
PhotoSmart TouchSmart Web All-in-One Printers

HP 920 printhead CN643A - CD868-3001:

OfficeJet 6500 Series
OfficeJet 6500 Wireless
OfficeJet 7000
PhotoSmart B109A B109N B109C B109D B109f
PhotoSmart B209 Series
PhotoSmart Plus

Comments

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

Fix your printer !

Search This Blog