Skip to main content

How to fix error code 0x61011be5 or ox61011be5 on HP printers



General Printer Error 0x61011be5.

Appears on these printers: D7560, C309A, C5390, C6380, ...

Genraly it's a carriage jam or a printhead issue.

Solution 1: Do a reset of the printer to factory default settings
    • Verify that the unit is switched on. 
    • Disconnect the  power cable from All-in-One and also from wall outlet.
    • Wait a minute.
    • Plug in the power cable to the printer and also to wall outlet.
    • Unplug the power cable from the printer (with the printer powered on) and wait for 20 seconds.
    • Then, press and hold "#" and "6" while plugging in the power cord.
    • Release the buttons after connect power cord.


      Solution 2:
        • Open the printer and wait for the carriage to slide over
        • Remove the ink cartridges from the print head.
        • With a cotton swabs dipped in hot water, clean gently the print head and each ink cartridge, until there is no ink residue coming off on the cotton swab.
        • Once all is dry, replace the cartridges
        • Do a print test.
        • If the error is still here: there are  two possibilities:
        • One of the ink cartridges is defective and causing the error
          The print head will need to be replaced. (CN642A)


          Comments

          Anonymous said…
          1.) Download and install "Canon My Printer" then open it and click on troubleshooting till you are called to print a test page. Click yes. Then the error will appear (b200).

          2.) Do it like you always do when you want to reach to your ink cartridges then click at print at the dialog above. It will print and that helped me to solve this error.

          Sorry for my english. ^^
          Unknown said…
          My MX850 was 5 years old and when I turned it on it showed the B200 error. I followed all the suggestions, removed printhead, and cleaned with warm water, put in new cartridges and still got B200 error so I sent it to the recycle place. I had another printer that I had purchased for photographs so will stick with Canon. Sometimes these things just wear out.
          Anonymous said…
          It seems that solution #3 almost works,but when I'm about to print a test page,error B200 reappears.I would not hesitate to buy a new printer head for my MP 560 if I knew it would solve the problem,but supposed this doesn't work.That would mean $50.00 down the drain.

          Popular posts from this blog

          How to fix error B200 on canon Printers

          MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

          How to solve error code 006 with Canon Service Tool V3400

          MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

          How to solve error B204 on Canon Maxify printers

          The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr