Brother DPC-8150, DCP-8150DN: How to Enter Maintenance Mode

Here is the procedure to enter Maintenance mode with Brother DCP-8150:

Switch on the printer
Press "Menu", then "Start", then "Menu" button
"0" is displayed on the LCD.
With the keypad, enter the maintenance mode function code to be executed.
Each time the selected maintenance mode function is completed, the machine returns to the ready state automatically.

List of Maintenance Mode Functions:

01 Initialize EEPROM parameters
05 Print white level/black level data for document scanning
compensation
06 Move CIS unit to transportation position
08 ADF performance test
09 Print test pattern
10 Set worker switches (WSW)
11 Print worker switch (WSW) setting data
12 Check LCD operation
13 Check control panel button operation
25 Display software version
32 Check sensor operation
33 Display LAN connection status
43 Set PC print functions 1.3.12
45 Change USB No. return value / Adjust left-end print start position on second side when duplex printing / Change ON/OFF setting for Deep Sleep function
52 Set country / language
53 Transfer received fax data/log information
54 Fine-tune scanning position
55 Acquire white level data and set CIS scan area
61 Adjust touch panel
67 Continuous print test
69 Print frame pattern (single-side printing)
70 Print frame pattern (duplex printing)
71 Print solid pattern
74 Setting by country
77 Print maintenance information
78 Check fan operation
80 Display machine log information
82 Display machine error code
87 Send communication log information to telephone line
88 Reset counters for periodic replacement parts
91 Initialize EEPROM parameters
99 Quit maintenance mode

Comments

Unknown said…

When the industrial inkjet printer is running, although the ink and solvent is well sealed in the vessel, the organic chemistry is volatile all the time, especially in hot summer.
national coding

July 7, 2014 at 11:22 PM

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

Fix your printer !

Search This Blog