Skip to main content

How to solve message "Remove and check cartridge" on HP printers


The message "Remove and check cartridge" or "Remove and check color cartridge" means a cartridge could be defective. 

Before replacing the cartridge, try these solutions:



Solution 1 : for some HP printers
  • Chech the door at the back of the printer. It must be closed.


Solution 2: (for HP PSC 1503, 1504, 1507, 1508, 1510, 1510v, 1510xi, 1513 et 1514)

Solution 3: reset the printer:
  1. Power off the printer.
  2. Remove the power cable from the back of the printer.
  3. Wait for 2 minutes.
  4. Connect the power cable to the printer.
  5. Switch on.

Solution 4:
  • Remove the faulty cartridge.
  • Power of the printer and close the door.
  • Switch on the printer: the screen says you have to install a cartridge. Put it back.

Solution 5:
  • A faulty sensor can lead to this error.
  • Slamming the door (not too strong !) can solve the problem
Libellés :

Comments

Anonymous said…
Thank you for all the info! My printer is fairly new so I don't know how to operate is yet but I have a feeling I will the info you have given.
April 16, 2013 at 1:34 PM
Anonymous said…
I tried solution #4 on my very old HP6110 all-in-one. This worked like a charm. Thank you.
June 4, 2013 at 6:26 PM
Post a Comment

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges ...
217 comments
Read more

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool
11 comments
Read more

Service tool V3400 for resetting Canon printers counter

MAJ13/02/18 The Service Tool V3400 , and service tool V3600 , allow you to reset the waste ink pad counter on some Canon printers:  You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 There is too a paid version here: V3400 C...
40 comments
Read more