Skip to main content

How to reset waste ink pad on Canon Pixma MP280

Error P07 means the waste ink counter is full.

Solution 1:
  1. First, search and download the Service Tool V1074.

  • Turn off the printer
  • Hold down the "stop/reset" and press the "power" button without release it.
  • Release the "stop/reset".
  • Press the "stop/reset" button six times and release the two buttons.
  • The printer is now in service mode.
  • Extract the Service tool and the file to open service tool page
  • Find the "clear ink counter" section and click on the "main" button.
  • Scroll down to find "ink absorber counter" on the left and to the right of that "counter value".
  • Ink absorber counter box should read "main" and counter value reads "0".
  • Click the set button to the right of the counter value box.
  • The printer will now make some noise and will print a page of paper,.
  • A message will tell you when the process has been completed.
  • Click on the prompts.
  • Turn the printer off wait a few seconds and turn it back.

Solution 2:
  • Unplug power and USB cable.
  • Open door and hold power button.
  • Connect power.
  • Close door, then release power button.  

Solution 3:

Comments

Anonymous said…
How to Reset waste ink counter (Error E16)

Close door, then release power button.
After this my printer turn off.. So then? What to do???
Anonymous said…
How to Reset waste ink counter (Error E16)

Close door, then release power button.
After this my printer turn off.. So then? What to do???

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr