Skip to main content

Solutions for error code Oxc19a0013 on HP printers

MAJ 27/07/15

The error Oxc19a0013 or 0xc19a0013  appears on these printers C5180, C5380,  C6280, C6380, C7280, D7360, 6100...



Solution 1:

  • Make sure that the product is turned on and then disconnect the USB cable from the back of the product.
  • Open the product cover and remove the cartridges.
  • Close the cover and wait for a message to insert the cartridges to appear on the control panel display.
  • Disconnect the power cord from the back of the product.
  • Disconnect the power cord from the wall outlet and wait for one minute.
  • Reconnect the power cord to the wall, reconnect the other end of the power cord to the product, and then turn on the product if it is not already on.
  • Open the product cover and reinstall the cartridges.
  • Close the cover and print a calibration page, if prompted.
  • Print a self test report to make sure that the product can print.
  • Reconnect the USB cable between the product and the computer.
  • Try to print a document from an application on the computer.

Solution 2:
  • Remove a print cartridge to make sure the plastic tape has been removed. If it is still covering the ink nozzles, gently remove the plastic tape by using the pink pull tab. Do not touch the ink nozzles or the copper-colored contacts.
  • Reinsert the print cartridge.
  • Repeat steps 1 and 2 for the other print cartridge.
  • If the problem persists, print a self-test report to determine if there is a problem with the print cartridges.
  • This report provides useful information about your print cartridges, including status information.
  • If the self-test report shows a problem, clean the print cartridges.
  • If the problem persists, clean the copper-colored contacts of the print cartridges.


Solution 3:
  • Remove the cartridges
  • Remove the printhead and clean the 3 areas below:

Solution 4:
  • Somes users have solve this error with the setup cartridge...


Solution 5:
  • The printhead could be defective

Comments

Anonymous said…
It does not work.
Anonymous said…
This solution does not work. Nothing but problems with this piece of junk.
Carlo Bonzi said…
mi hai preso per un pirla passo e chiudo? Ma che indicazioni del menga hai inserito?Quersto errore e' dovuto all'uso di testine non originale e quindi occorre resettare l'errore con software oppure con applicazioni di nastro sui primi due contatti poi reinserire togliere nastro e coprire altri contatti e poi reinserire..andate su youtube e vedrete tutta la manovra per validare la cartuccia,
Clasz said…
None of your solutions work. I thought I was buying a high quality printer because of the brand name HP. so disappointed I bought a full set of new ink cartridges for $127 and this too has not fixed the problem. Yes a piece of Junk
MemphisZ said…
Me to! Tried all the methods...after buying new cartridges!

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr