Brother MFC-9420CN error list

Error list:

20 - Laser power error
21 - Beam detector error
22 - Nvram error
23 - Engine controller error
24 - Process timing clock error
25 - Developing motor error
26 - Main motor error
27 - Scanner motor error
28 - Charge HV unit error
29 - LVPS error
2A - Fuser thermistor error
2B - Fuser heater error
2C - Fuser temperature low error
2D - Fuser temperature low error
2E - Fuser temperature high error
2F - Fuser ACOFF error
30 - Erase LED error
31 - Power supply fan error
32 - Exit fan error
33 - Laser unit fan error
34 - Yellow switching clutch error
35 - Magenta switching clutch error
36 - Cyan switching clutch error
37 - Black switching solenoid error
38 - Yellow switching solenoid error
39 - Magenta switching solenoid error
3A - Cyan switching solenoid error
3B - Black switching solenoid error
3C - Transfer belt error
3D - Transfer roller solenoid error
3E - Transfer roller solenoid error
3F - Fuser unit clutch error
40 - Belt marker sensor error
41 - HVU connection error
42 - Toner empty sensor error
43 - Toner empty sensor error
44 - Lower feeder unit error
81 - Recording paper jam
82 - Recording paper jam
83 - Recording paper jam
84 - Recording paper jam
85 - No papertray
88 - Recording paper jam
8A - The main motor does not rotate
8B - The main motor stops suddenly
A1 - Front cover (scanner unit) front cover
A2 - Document jam
A3 - Document jam
A5 - FAX scanning failure
A6 - FAX scanning failure. (retry)
AB - CIS Resolution failure
AF - CIS positioning error
B7 - A/D converter reference
B9 - Light emission intensity error
BB - White level data error
BD - Black level data error
D0 - DF - Modem error
E6 - Write error in EEPROM
E8 - Data scanning error
EA - Document removed at phaseB
F8 - Battery connection error

Comments

Jimmy777777 said…

Cover the two side hole sensors with paper and tape. That will stop the message.

February 10, 2012 at 11:23 AM

Printer Clinic said…

Nice post to share, I am always interested in printer related topic to share for people on internet as I wrote in my niche printer specific blog.

February 1, 2014 at 4:24 AM

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

Fix your printer !

Search This Blog