Skip to main content

Brother MFC-9420CN error list


Error list:

  • 20 - Laser power error
  • 21 - Beam detector error
  • 22 - Nvram error
  • 23 - Engine controller error
  • 24 - Process timing clock error
  • 25 - Developing motor error
  • 26 - Main motor error
  • 27 - Scanner motor error
  • 28 - Charge HV unit error
  • 29 - LVPS error
  • 2A - Fuser thermistor error
  • 2B - Fuser heater error
  • 2C - Fuser temperature low error
  • 2D - Fuser temperature low error
  • 2E - Fuser temperature high error
  • 2F - Fuser ACOFF error
  • 30 - Erase LED error
  • 31 - Power supply fan error
  • 32 - Exit fan error
  • 33 - Laser unit fan error
  • 34 - Yellow switching clutch error
  • 35 - Magenta switching clutch error
  • 36 - Cyan switching clutch error
  • 37 - Black switching solenoid error
  • 38 - Yellow switching solenoid error
  • 39 - Magenta switching solenoid error
  • 3A - Cyan switching solenoid error
  • 3B - Black switching solenoid error
  • 3C - Transfer belt error
  • 3D - Transfer roller solenoid error
  • 3E - Transfer roller solenoid error
  • 3F - Fuser unit clutch error
  • 40 - Belt marker sensor error
  • 41 - HVU connection error
  • 42 - Toner empty sensor error
  • 43 - Toner empty sensor error
  • 44 - Lower feeder unit error
  • 81 - Recording paper jam
  • 82 - Recording paper jam
  • 83 - Recording paper jam
  • 84 - Recording paper jam
  • 85 - No papertray
  • 88 - Recording paper jam
  • 8A - The main motor does not rotate
  • 8B - The main motor stops suddenly
  • A1 - Front cover (scanner unit) front cover
  • A2 - Document jam
  • A3 - Document jam
  • A5 - FAX scanning failure
  • A6 - FAX scanning failure. (retry)
  • AB - CIS Resolution failure
  • AF - CIS positioning error
  • B7 - A/D converter reference
  • B9 - Light emission intensity error
  • BB - White level data error
  • BD - Black level data error
  • D0 - DF - Modem error
  • E6 - Write error in EEPROM
  • E8 - Data scanning error
  • EA - Document removed at phaseB
  • F8 - Battery connection error

Comments

Jimmy777777 said…
Cover the two side hole sensors with paper and tape. That will stop the message.
Printer Clinic said…
Nice post to share, I am always interested in printer related topic to share for people on internet as I wrote in my niche printer specific blog.

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Service tool V3400 for resetting Canon printers counter

MAJ 11/06/17 The Service Tool V3400, and service tool V3600, allow you to reset the waste ink pad counter on some Canon printers: 

You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers:
Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240 Canon MX397, MX320, MX330, MX860 etc
Where can you download the Service Tool V3400 ?

It is free here:
ST V3400. (but check first for no virus or trojan)
There is too a paid version here:
V3400 Canon Service Tool for all iPxx…

Error 6000 or P03 on Canon printers

MAJ11/06/17
Error code 6000, P03 or E23 is a line feed error. It also should be flashing 3 times for this error on the on/off button.

You can have this error on these Canon printers: MP140, MP150, MP160, MP190, MP210, MP220, MP170, MP180, MP450, MP460, MP240, MP250, MP260, MP270, MP480, MP500, MP510, MP520, MP530, MP830, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100, MP640, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200,


Solution 1:
Verify that the paper tray is correctly set.If any object is placed in front of the machine, remove it.
Solution 2:
Search for any small pieces of paper in the printer, or a tiny object.
Solution 3:
Power off the printerWait 5 minutePower on. 
Solution 4:
Clean the encoder strip with a soft clothSolution 4a:
Clean the printhead
Solution 5: one of these parts could be faulty:
Timing sensor unit QM2-2683Timing slit disk film QC1-6229Feed roller ass'y QL2-0925Platten unit QM2-2923Logic board…