Skip to main content

Reset purge counter for Brother MFC-J265W


To reset the purge counter of Brother MFC-J265W:
  • Unplug the power cable.
  • Hold down the "Start" button.
  • Without release the "Start" button, connect the power cable.
  • When "Maintenance" appears on the screen, release the "Start" button.
  • Enter 80 with the numerical keypad.
  • With down button go to the purge counter: "Purge00xxx"
  • Enter 2783 with the numerical keypad.
  • Press on "Stop/Exit" to go back in Maintenance mode
  • Enter 9 and 9 to quit the Maintenance mode.

This solution is available for these Brothers printers too:
  • MFC-210C, MFC-215C, MFC-235C, MFC-260C, MFC-240C, MFC-250C, MFC-255CW, MFC-295CN, MFC-297C
  • MFC-3240C, MFC-3340CN, MFC-3342C, MFC-3360C
  • MFC-410CN, MFC-420CN, MFC-425CN, MFC-440CN, MFC-465CN, MFC-490CW
  • MFC-5440CN, MFC-5840CN, MFC-5460CN, MFC-5860CN, MFC-5490CN, MFC-5890CN, MFC-5895CW,
  • MFC-620CN, MFC-640CN, MFC-640CW, MFC-660CN, MFC-665CW, MFC-680CN, MFC-6490CW, MFC-6890CDW
  • MFC-790CW
  • MFC-820CW, MFC-845CW, MFC-885CW, 
  • MFC-990CW, 
  • MFC-J220, MFC-J265W
  • MFC-J410, MFC-J415W, MFC-J430W
  • MFC-J5910DW
  • MFC-J615W, MFC-J625DW, MFC-J6510DW, MFC-J6710D, MFC-J6710DW, MFC-J6910DW, 
  • MFC-J825DW

Comments

Anonymous said…
wow ...
normanio said…
This comment has been removed by the author.
Anonymous said…
thank you bro, my brother printer is good as new.
Anonymous said…
The method is good, thank you bro

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Service tool V3400 for resetting Canon printers counter

MAJ 11/06/17 The Service Tool V3400, and service tool V3600, allow you to reset the waste ink pad counter on some Canon printers: 

You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers:
Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240 Canon MX397, MX320, MX330, MX860 etc
Where can you download the Service Tool V3400 ?

It is free here:
ST V3400. (but check first for no virus or trojan)
There is too a paid version here:
V3400 Canon Service Tool for all iPxx…

Error 6000 or P03 on Canon printers

MAJ11/06/17
Error code 6000, P03 or E23 is a line feed error. It also should be flashing 3 times for this error on the on/off button.

You can have this error on these Canon printers: MP140, MP150, MP160, MP190, MP210, MP220, MP170, MP180, MP450, MP460, MP240, MP250, MP260, MP270, MP480, MP500, MP510, MP520, MP530, MP830, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100, MP640, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200,


Solution 1:
Verify that the paper tray is correctly set.If any object is placed in front of the machine, remove it.
Solution 2:
Search for any small pieces of paper in the printer, or a tiny object.
Solution 3:
Power off the printerWait 5 minutePower on. 
Solution 4:
Clean the encoder strip with a soft clothSolution 4a:
Clean the printhead
Solution 5: one of these parts could be faulty:
Timing sensor unit QM2-2683Timing slit disk film QC1-6229Feed roller ass'y QL2-0925Platten unit QM2-2923Logic board…