Skip to main content

Printer Brother DCP-6690CW

Download:


Cartridges:
  • LC1100BK: Black ink cartridge
  • LC1100C: Cyan ink cartridge
  • LC1100M: Magenta ink cartridge
  • LC1100Y: Yellow ink cartridge


Troubleshootings:
  • How to factory reset the network settings:

  1. Make sure the machine is not operating, then disconnect all the cables from the machine (except the power cord).
  2. Press Menu.
  3. Press the up or down arrow key to choose Network and press OK.
  4. Press the up or down arrow key to choose Factory Reset or Network Reset and press OK.
  5. Press + for Reset.
  6. Press + for Reboot.
  7. The machine will restart, re-connect cables once this is complete.
For Touchscreen models:
  1. Make sure the machine is not operating, then disconnect all the cables from the machine (except the power cord).
  2. Press MENU.
  3. Press Network.
  4. If Network Reset is in the options, press Network Reset.
    If not, press the up or down arrow key to display Factory Reset and press Factory Reset.
  5. Press Yes.
  6. Hold down Yes for 2 seconds to confirm.
  7. The machine will restart, re-connect cables once this is complete


  • Message "Unable to print 50":
- Lift cover. Remove the two plastic panels covering wires. Mark down position of cables then remove them, and remove the now-freed top scanner section entirely.
- Remove screws from top plastic shell. There's two in the back and four in the front. There's also two plastic tabs in the front that must be bent aside before you can remove the top shell.
- Gently put the encoder strip back in its plastic guide. (the posted pic is actually a decent illustration of it.).

  • Message "Unable to print 70"
Libellés :

Comments

Post a Comment

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr
217 comments
Read more

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool
11 comments
Read more

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr
2 comments
Read more