Skip to main content

Fixing Error 13.xx on HP Laserjet

3.XX PAPER JAM [LOCATION]
  • Media is jammed at the specified location (and possibly at other locations). If the message persists after all jams have been cleared, a sensor or sensor lever might be stuck or broken. 
  • For all jam messages, do the following: 
  • 1. Remove jammed print media from the specified location. Check the entire paper path for other pieces of media in the path. 
  • 2. Open and close the top cover to clear the message. 
  • 3. Check sensors and flags in the paper path for proper operation.
3.0 PAPER JAM [LOCATION]
  • A non-specific paper jam occurred. 
  • 1. Remove jammed media from the specified location. 
  • 2. Verify the paper tray is fully closed. 
  • 3. Inspect and/or replace the feed and separation rollers. 
  • 4. Ensure there is no obstruction in the path, such as a torn piece of paper. 
  • 5. Open and close the top cover to clear the message. 
  • 6. Check sensors and flags for proper operation.

13.1 PAPER JAM OPEN INPUT TRAYS
  • Paper-delay jam at paperfeed area. 
  • 1. Ensure that paper trays are loaded and adjusted properly so media can feed from the tray. It might be necessary to reduce the stack height of media in the tray. 
  • 2. Check the input area for obstructions such as media in the path. Also check to see if the registration assembly damaged or unseated. 
  • 3. Replace any defective sensors or flags. 
  • 4. Verify the media meets the specifications. 
  • 5. Check the pickup feed and separation rollers for unusual wear. Replace as needed. 
  • 6. Rotate the media in the input tray by 180° and/or turn it over On NX engines this is most likely the fuser flag or the ACPM. The ACPM has a photosensor hard-wired to the back of it.

13.10 PAPER JAM CHECK DUPLEXER
  • Jam at duplexer. 
  • 1. Check the duplexer and the rear area of the printer for obstructions or damage. 
  • 2. Check the duplexer for proper operation. Replace the duplexer if a sensor is defective. On a 5si, 8000, or 8100 series laserjet a Duplex Jam can be caused by a tray 2 and 3 feed assembly failure.

13.14
  • For Laserjet 5si. This error is caused by a defective paper control PCA Replace paper control PCA.
13.2 PAPER JAM OPEN INPUT TRAYS
  • Paper-stopped jam at paper-feed area. 
  • 1. Check the input area for obstructions such as paper in the path. Also check to see if the registration assembly is damaged or if the transfer roller is out of place. 
  • 2. Replace any defective sensors or flags. 
  • 3. Ensure the media does not exceed the maximum length. 
  • 4. If multiple sheets are feeding, it might be necessary to fan the media and reduce the stack height. Also, replace separation pad. 
  • 5. Verify that the fuser is properly installed. On NX engines this is an input jam.
13.20 PAPER JAM CHECK REAR DOOR
  • Media stopped in the paper path during power on or when the top door was closed. 
  • 1. Remove all media in the paper path, and then open and close the top cover. 
  • 2. If the message persists after all media is removed: Check if media is jammed in the prefeed area. Replace any defective sensors or flags

13.21 DOOR OPEN JAM
  • The top cover was open while printing. 
  • 1. Clear the jam and close the top door. 
  • 2. If the message persists, check the top door switch for proper operation.
13.5 PAPER JAM CHECK REAR DOOR
  • Paper-delay jam at fuser. 
  • 1. Check the transfer roller and small media belt to ensure they are operating and can feed print media. 
  • 2. Check the paper path for obstructions at the transfer roller, toner cartridge, paper feed assembly, and fuser. 
  • 3. Replace any defective sensors or flags. 
  • 4. Turn the media stack over and/ or rotate it by 180° in the input tray. If still persists - replace fuser, then DC controller.
13.6 PAPER JAM CHECK REAR DOOR
  • Paper-stopped jam at fuser. 
  • 1. Check the paper path for obstructions at the fuser and output/delivery area. 
  • 2. Replace any defective sensors or flags.
13.99 PAPER JAM [LOCATION]
  • A non-specific paper jam occurred. 
  • 1. Remove jammed media from the specified location. 
  • 2. Verify the paper tray is fully closed. 
  • 3. Inspect and/or replace the feed and separation rollers. 
  • 4. Ensure there is no obstruction in the path, such as a torn piece of paper. 
  • 5. Open and close the top cover to clear the message. 
  • 6. Check sensors and flags for proper operation
Libellés :

Comments

Post a Comment

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges ...
217 comments
Read more

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool
11 comments
Read more

Service tool V3400 for resetting Canon printers counter

MAJ13/02/18 The Service Tool V3400 , and service tool V3600 , allow you to reset the waste ink pad counter on some Canon printers:  You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 There is too a paid version here: V3400 C...
40 comments
Read more