Minolta 1080 error code list

C000	Main drive problem
C001	Main drive speed. Too fast or too slow
C004C	Fan motor problem
C004E	Power supply fan problem
C0070	Toner motor drive problem
C0071	Toner motor speed. Too fast or too slow
C010	Drum motor drive problem
C011	Drum motor speed. Too fast or too slow
C0400	Exposure lamp does not turn on or AE sensor problem
C0500	Low fuser temperature during warm-up
C0510	Low fuser temperature after warm-up
C0520	High fuser temperature
C0600	Scan motor drive problem
C0610	Lens motor drive problem
C0620	Mirror motor drive problem
C0990, C0991	Main tray up problem
C0992, C0993	Main tray down problem
C0994	Elevator motor problem
C0996	Main tray shift problem
C0998	Tray shift problem
C0999	Tray shift return problem
C099A, C099b	Shift home problem
C099c	Shift drive motor
C0b10	Auto exposure sensor problem
C0b11	Paper clamp motor
C0b30	Paper aligning motor
C0b31	Paper aligning motor
C0b50	Stapler motor
C0b51	Stapler problem
C0b52	Stapler sensor
C0b60	Sorter bin motor
C0b61-C0b64	Sorter bin movement
C0d00	Duplex rail sensor sensor problems
C0d20	Duplex home sensor
C0d50	Duplex drive motor problem
C0d51	Duplex drive motor speed
C0F10	Auto exposure sensor problem
C0F30	Paper aligning motor
C4100	Exposure lamp stays on
C0F79	Paper empty sensor problem

Comments

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

Fix your printer !

Search This Blog