Skip to main content

Waste ink absorber reset on Canon IP1700



Solution 1:
  • First power off the printer. Next, while holding STOP/RESET button, power on the printer.
  • While holding POWER button, release STOP/RESET button. Then push STOP/RESET button twice.
  • Wait about 20-30 second until the LED shows “0″. Then push STOP/RESET button four times.
  • Finally push POWER button twice. Last step is to turn off the printer by pressing the POWER button one last time.

Solution 2:
  • Unplug power and USB cable.
  • Open door and hold power button.
  • Connect power.
  • Close door, then release power button.

Solution 3:
  • Turn Off the printer, and then take off the cable power.
  • Push and hold the power button
  • Connect again the power cable.
  • Use your middle finger to push the resume button 2 times.
  • Release the power button.

Comments

Rahul Goyal said…
Thanks for nice sharing. You can also find latest Printing technology in Splashjet.co.in. Printing technology has witnessed a sea change with the advent of modern printers, latest software and advanced printing methods. For more information Visit canon printer ink

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17
Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below:


Solution 1:
Disconnect the power cable from the printer.Wait 1 hour.Connect the power cable
Solution 2:
Check and Clean Head contact pin condition of the carriage unitCheck Cable connection especially the carriage FFC
Solution 3:
Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left.Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on
Solution 4:
Unplug the power cable.Open the printerPush the whole print head mechanic to the centerWhile the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. 
Solution 4a:
Take out all of the ink cartridgesLift up the grey bar by where the ink goesLeft the print head in the middle of the pr…

Error 6000 or P03 on Canon printers

MAJ11/06/17
Error code 6000, P03 or E23 is a line feed error. It also should be flashing 3 times for this error on the on/off button.

You can have this error on these Canon printers: MP140, MP150, MP160, MP190, MP210, MP220, MP170, MP180, MP450, MP460, MP240, MP250, MP260, MP270, MP480, MP500, MP510, MP520, MP530, MP830, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100, MP640, MP990, MG5200, MG5300, MG6100, MG6200, MG8100, MG8200,


Solution 1:
Verify that the paper tray is correctly set.If any object is placed in front of the machine, remove it.
Solution 2:
Search for any small pieces of paper in the printer, or a tiny object.
Solution 3:
Power off the printerWait 5 minutePower on. 
Solution 4:
Clean the encoder strip with a soft clothSolution 4a:
Clean the printhead
Solution 5: one of these parts could be faulty:
Timing sensor unit QM2-2683Timing slit disk film QC1-6229Feed roller ass'y QL2-0925Platten unit QM2-2923Logic board…

Error U052 on Canon printers

MAJ 14/10/14
Error U052 appears on these Canon printers: MX850, MP540, MP530, MP600, MP610, MP970 and others...

Message error: The type of print head is incorrect install the correct print head U052



Solution 1:
Remove and replace the cartridges.
Solution 2:
Insert new cartridges
Solution 3:
Reseat the print head to correct print issues or clear error.
Solution 3a (thanks to Tony LeBaigue):
Remove the ink cartridges.Remove the printhead: cleaned the rear contacts with a cotton bud and surgical spirit.Left the part 5 minutes to dry.Install the printhead and the cartridges. The printer wil be into printhead clean mode and will return to normal mode.
Solution 3b (thanks to Arjen - Canon MP610):
Power off the printer. Press and hold both selection buttons underneath the screen, and switch on the printer. After a long start up the 'copy' screen appeared, and it printed a copy of a sheet.
Solution 4:
Clean the printhead
Solution 4a:
The print head is broken and it must be changed by a new one…