Skip to main content

Dell Laserjet 1600 parts list


Parts list for this printer:
  • N5696 110V Engine Power Board Assembly
  • N5796 110V Fuser
  • M5517 ADF Engine Assembly
  • M5914 ADF Lower Cover Assembly
  • M5512 ADF Pickup Assembly
  • 4M346 ADF Rubber Pad
  • K5751 ADF Top Cove
  • G5112 Base Assembly (LOUISIANA, 110V)
  • C5212 Bezel, Prt
  • R5378 Exit Sensor
  • U4718 FAX Terminator Plug, 1600n/
  • P5150 Front Door Cover
  • N5672 Left Front Cover Support
  • K5684 Left Side Cover
  • N5682 Main Fan (1-wire)
  • AD0624MS-A70GL Main Fan (1-wire)
  • J5946 Main Gear Assembly
  • D5043 Main Paper Output Tray
  • R5080 MODEM, Card
  • R5073 Onal 250-Sheet Paper Tray
  • R5074 OP Panel Controller Board
  • R5075 Op Panel Extension Cover (Paper-Clip Tray)
  • D5035 Op Panel Overlay
  • R5078 Pass-Through Paper Door
  • 7Y600 Power Cord
  • C5210 Primary 250-sheet Paper Tray
  • N5668 Printhead
  • N5640 Rear Cover
  • N5674 Right Front Cover Support
  • J5907 Right Side Cover
  • R5077 Scanning Unit Assembly
  • U5171 Transfer Roller

Comments

Popular posts from this blog

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug  the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr