Skip to main content

Error code "6A" on Brother MFC


Error code 6A is a fuser error. It appears on Brother MFC-8440, MFC-8840, MFC-8500, DCP-8020, DCP-8040, DCP-8045D


Solution 1:
  1. Turn off the power
  2. Unplug the printer power.
  3. Wait 5 minutes.
  4. Plug the power cord back in.

Solution 2:

    Solution 3:
    • Unplug for 10 seconds
    • Press and hold on the menu key while you plug it back in untill you see the screen "parameter init" 
    • Press 99.  

    Solution 4:
    • Turn off printer
    • Hold down MENU button and turn on.
    • Release the button after 5 seconds.
    • f error still occurs, press 9,1
    • If error still occurs, press 9,9

    Solution 5:
    • Replace the fuser
    • Fuser for MFC-8440, MFC-8840, DCP-8020, DCP-8040, DCP-8045D: LM2578001 
    Libellés :

    Comments

    Anonymous said…
    GRACIAS
    April 24, 2016 at 7:49 AM
    Post a Comment

    Popular posts from this blog

    How to fix error B200 on canon Printers

    MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges ...
    217 comments
    Read more

    How to solve error code 006 with Canon Service Tool V3400

    MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes.  If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool
    11 comments
    Read more

    Service tool V3400 for resetting Canon printers counter

    MAJ13/02/18 The Service Tool V3400 , and service tool V3600 , allow you to reset the waste ink pad counter on some Canon printers:  You can solve the messages errors "Waste Ink Tank Full" or "Waste Ink Pad Full", "error 5B00" or "Error P07" on these printers: Canon Pixma iP2700, iP4800, iP4810, iP4840, iP4850, iP4900, iP4910, iP4940, iP4970, iP4980, iP4990, iP5810, iP5880 Canon Pixma MP230, MP240; MP250; MP260; MP270; MP280; MP480; MP490; MP540; MP550; MP560; MP620; MP630; MP640; MP980; MP990; Canon Pixma IX6500, IX6510, IX7000 Canon Pixma IP3600, IP4940 Canon Pixma PRO9000, PRO9500 Canon Pixma MG2120. MG2140, MG2240, MG2250, MG2440, MG3240, MG3140, MG4100, MG4140, MG5140, MG5150, MG5240, MG5340, MG6140, MG6240, MG8140, MG8240  Canon MX397, MX320, MX330, MX370, MX860  etc Where can you download the Service Tool V3400 ? It is free here: https:/ /1fichier. com/ ?c198556kp0 There is too a paid version here: V3400 C...
    40 comments
    Read more