How to solve error E015-0001 on Canon i-SENSYS MF series printers

Here are some solutions to solves error code 015-0001 on printers Canon i-SENSYS MF623C, MF8350Cdn, mf9280cdn, etc

Solution 1: Description Developing roller release operation defect

After the specified time from rotating the main motor for the developing roller depress/release, the output of the developing home position sensor does not change.
Causes: Developing home position sensor defect, Main motor defect, DC controller PCB defect
Remedy:

Check the connector of the developer home position sensor, main motor, DC controller PCB
Replace the developer home position sensor
Replace the main motor
Replace the DC controller PCB

Solution 2: Cassette 1 lift-up errorAfter lift-up of the Lifting Plate of the cassette of the host machine started, ON status of the Lifter Sensor of the cassette of the host machine was not detected within the specified period of time.

Remedy. While the cassette of the host machine is removed, turn ON the power and insert the cassette, then check the operation sound of the motor.
When there is operation sound of the motor, check if the Lifting Plate has been lifted up.
When the Lifting Plate has been lifted up:
1-1. Check that the Lifter Sensor of the cassette of the host machine is properly installed.
1-2. Check the harness/connector between the Engine Controller PCB and the Lifter Sensor.
1-3. Replace the Lifter Sensor.1-4. Replace the Engine Controller PCB.
When the Lifting Plate has not been lifted up:
2-1. Check the condition of the gear at the host machine side (missing teeth, swing).
2-2. Check the harness/connector between the Engine Controller PCB and the Lifter Solenoid of
the cassette of the host machine.
2-3. Replace the Lifter Solenoid.
2-4. Replace the Pickup Motor of the cassette of the host machine.
2-5. Replace the Driver PCB.
2-6. Replace the Engine Controller PCB.
When there is no operation sound of the motor, check the followings:
3-1. Check the harness/connector between the Engine Controller PCB and the Pickup Motor of
the cassette of the host machine.
3-2. Check the condition of the gear at the host machine side (missing teeth, swing).
3-3. Check the Pickup Motor.
3-4. Replace the Driver PCB.
3-5. Replace the Engine Controller PCB.

Comments

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON. When the printhead still moving and is going to the very LEFT, close the cover. Wait until its boot up. Solution 4a: Take out all of the ink cartridges Lift up the gr

How to solve error code 006 with Canon Service Tool V3400

MAJ 25/08/17 The Service Tool V3400 allow to reset the counter of some Canon printers. For the error code 006 , try this : Solution 1: Check your cartridges: an empty cartridge can lead to error 006 Solution 2 : After you avec clicked on "Main", wait a few minutes. If the error still here, restarts the Service Tool Solution 3 : Close the service tool Disconnect the USB cable from the printer After 10 seconds, plug back the cable to the printer On Windows, click next when appears "New device" Open the service tool

How to solve error B204 on Canon Maxify printers

The error B204 could happen after a cartridge replacement. First of all, when installing, remove the cartridges from the plastic package, but do not drill any plastic membranes, as this will cause this error when placing the cartridge. The error may also appear if you change a completely empty cartridge: when installing a full cartridge, the printer enters a cleaning cycle, but the printhead has not yet received ink from the newly inserted cartridge. Here are some tips to cancel this error B204:: Solution 1: Remove the cartridges Power the printer for 2 minutes Switch on the printer Install the cartrdiges Solution 2: Switch on the printer Unplug the power cable Open the cover Move the print head carriage manually to the usual place where it goes for the cartridge change (If the printhead carriage is not movable, reconnect and then turn on the printer, then unplug it again when the head carriage is in the moving position). Change the cartridges. Close the fr

Fix your printer !

Search This Blog