Skip to main content

Posts

Showing posts from March, 2014

How to solve error code E000732-0001 on Canon copiers

You can have error code E000732-0001 on these Canon copiers: canon imageRunner 3200n, IR 3180, IR 7095, IR C2620, IR 5185n, IR 5570, IRC5185i, IR C3200, etc... Solution 1 : Check all the cables outside of the printer: they must be plugged, especially between the differents elements of the copier:  Solution 2 : Check all the connectors on the main board. Solution 3 : Unplugg and replugg all the leads between the boards and modules

Message error "Type of print head in incorrect. Install correct print head" on Canon printers

The message " Type of print head in incorrect. Install correct print head " may be followed with error code U052 . Solution 1: Reinstall the cartridges. If the error occurred after changing a cartridge: replace it. Solution 2: Reinstall the printhead. Solution 4 : Clean the printhead Solution 4: The print head is broken and must be replaced. Printhead list

Error E42 or 5010 on Canon printers

Eror code E42 or 5010 requires servicing... But, firt, try these two solutions. It could be a scanner dysfunction due to shock. Solution 1 : Open the right side of the printer (three screws) and release the plastic part. Reconnect the cable unplug. Reset the plastic part Solution 2 : Open the right side of the printer (three screws) and release the plastic part. There is a set of cables on the l eft : check that there is no one that is cut If this is the case: strip the cable, connect both ends and surround with electrical tape.

Error E315 with Canon IR2200, IR2800, IR3300

Error code E315 means any of the following is true in the image processing by the main controller: 1. The image data has a fault. 2. The encoding/decoding operation for image data has a fault. 3. The image processing element of the main controller PCB has a fault. The image data, the main controller or the HDD is faulty. What to do: If this error occurs during normal copying or printing, the job in question (image data) is cleared when the main power switch is turned off and then on again. If this error occurs frequently, however, a fault on the main controller PCB is a possibility. If this error occurs in a specific image within the Mail Box, damage in data may be assumed: be sure to delete the image from the Mail Box.

How to reset drum on OKI C5650

MAJ 27/07/15 Here is two procedures to reset the drum counter on OKI C5650 : Solution 1 : Turn the machine on while pushing and holding "Up" and "Down button at same time. Menu window will show "Oki User" Scroll to " Engine DialogMode" and push Enter button. "Diagnostic Mode xx.xx.xx S-Mode" is indicated. Scroll to "NV-Ram initial"  and push ENTER. Screen shows "NV-Ram- Initial Table 1". Push "Online" and "Enter" Buttons simultaneously and Hold for 10 seconds after you see "Executing Reset" in menu window. Restart printer. Solution 2 (if solution 1 does not work): Replace the chip on the drum :

Error 50.x on HP Laserjet P2030, P2035

Error 50.X is a fuser error :  the printer has experienced an error with the fuser. Solution 1: Turn off the power by using the power switch. Wait at least 60 seconds. Turn on the power and wait for the product to initialize.   Solution 2: If the error continues, turn off the product. Wait at least 25 minutes, and then turn on the product. (If you are using a surge protector, remove it. Plug the product directly into the wall socket. Use the power switch to turn on the product.)   Solution 3: Replace the fuser:  Hewlett Packard HP LaserJet P2035, P2055 Series Fusing Assembly (110-127V), Part Number RM1-6405 or RM1-6405-MK -N HP Maintenance Kit HP LJ P2035 P2055 110V

How to reset waste ink counter on a Canon Pixma Pro9500

Here is the procedure to reset waste ink absorber counter : Turn the printer power off. While pressing the "Resume/Cancel" button, press and hold the "Power" button. (The Power LED lights in green to indicate that a function is selectable.) While holding the "Power" button, release the "Resume/Cancel" button.  While holding the "Power" button, press the "Resume/Cancel" button 2 times, and then release both the "Power" and "Resume/Cancel" buttons. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.) When the Power LED lights in green, press the "Resume/Cancel" button 4 times to reset ink absorber counter. (Each time the Resume/Cancel button is pressed, the Alarm and Power LEDs light alternately, Alarm in orange and Power in green, starting with Alarm LED.) About Canon Pixma Pro9500 a