Skip to main content

Posts

Showing posts from April, 2012

Error E-01 on Epson printers

Error E-01 indicate the cartridges are empty: first, verify this is not the case. Solution 1 : Remove the cartridges Clean the chips with a soft cloth. Disconnect the power. Disconnect the USB cable. Hold on the "Power" button for 3 minutes then release. Connect USB and power cables. Power on the printer Install the cartridges Solution 2 : If error E-01 appears during the installation of a new cartridge: May be a the cartridge is defective. Replace it. Solution 3 : See also solutions for " unknown cartridge " message

Unknown cartridge message on Epson printers

Solution 1 : Remove all the cartridges. Close the door. Power off the printer. Disconnect the power. Disconnect the USB cable. Wait a minut. Connect the power cable Switch on the printer. Install the cartridges Close the door Power off. Power on. Connect the USB cable Solution 2: Vérifiy the chips of the cartridges: if necessary, clean the chips with a soft cloth. Solution 3: A cartridge is defective. Replace it.

Cold reset for HP Laserjet M5035

Procedure : Turn the off the device. Turn the device on and immediately hold down the 6 button on the control-panel keypad as soon as the control-panel display backlight illuminates. Continue to hold down the 6 button until all three control-panel LEDs remain illuminated. Release the 6 button. Use the 3 button or the 9 button to scroll to the desired low-level service mode function. Press 6 to select the desired low-level service mode function. Use the 3 button or the 9 button to scroll to function options. Press 6 to select a function option setting.

Canon I6500 printer

Cartridges : BCI-3EBK2 : Canon Black Twink pack BCI-3eBK/C/M/Y : Canon Multipack ink tank (Black, Cyan, Magenta, Yellow) Parts: Qy6-0034: Printhead QK1-1258-000: Power 220v/240v - 50/60H QG4-0087-000: Purge unit (QM2-2327) QA4-0323 : Ink absorber Troubleshooting : Reset waste ink counter: Press feed button hold on and press power button Press feed button twice Release feed and power button Wait a few seconds press feed button three time When green light standby unplug power printer Error 5C00 (orange light alternates with the green 4 times): problem with Purge cam sensor. Solution 1 : reset waste ink counter Solution 2 : Open the door of the printer Take out the cartridges Clean them gently Reinsert the cartridge in the printer

How to solve "System Error Cycle Power" on Samsung printers

This concern these printers: SCX-4828FN, SCX-4826, CLX-3170, CLX-3175... Solution 1 : Verify the USB cable connection. Insert it in a new USB port. Solution 2 : It's a fuser problem. Power off the printer and wait 5 minutes. Power on. If the error persist, replace the fuser Fuser parts for some Samsung printers: CLX-3170 series: JC96-04780A, JC96-05491A CLX-3175 series: JC96-04780A, JC96-05491A SCX-4828 series: JC96-05132A

How to solve 108.xx, 108.08 error on Lexmark printers

A 106.xx , 107.xx , 108.xx ,   or 109.xx  error indicates a problem with one of the printhead colors. Solution 1 : Power off the printer; Wait 5 minutes Power on. Solution 2: Connect the printer's power cord directly into a grounded wall outlet. A surge protector or uninterruptible power supply (UPS) can generate false error messages. Solution 3: Turn off the printer. Take off the back cover.  It turn out there is an IDE like cable that come out over the top edge of the motherboard. It is plugged into a receptacle that is also near the top of the edge of the motherboard.  Pull out the cable and re-insert it into its receptacle.  Also move the metal clip (already on the cable) over the receptacle.  Fire back up the printer and after a longish calibrating and setup period it will print out several reports and test pages just fine. Solution 4 : Contact Lexmark Technical Support

How to replace the fuser on Samsung CLX-3175 series

MAJ 08/01/15 Step 1: - Remose the right cover of the printer. - Remove both connectors (see photo below): Etape 2: - Remove the 4 screws fixing the fuser: - Move the handle as shown on the photo: Part number of the fuser: JC96-05491 More about the printers Samsung CLX-3175 series

How to replace the drum on Samsung CLX-3175 series

Procedure : Turn the machine off, then wait a few minutes for the machine to cool. Using the handle, completely open the front cover. Grasp the handles on the toner cartridge and pull to remove four cartridges from the machine. Pull the waste toner container out of the machine using its handle. Remove the imaging unit. Take a new imaging unit out of its package. Remove the protective devices on both sides of the imaging unit and the paper protecting the surface of the imaging unit. Holding the groove on the front of the imaging unit, push imaging unit into the machine. Procedure with pics : Manuel clx-3175fn (PDF - go to P.69) More about the printers CLX-3175 series

Cartridge error 50c on Lexmark X5150

Possible solution: when you insert your new or used cartridges youll need to go through a *auto alignment*: Turn off the printer . Open up the printer. Turn it back on. Take out both cartridged; clean them off and the inside of the printer as well close printer then look at the prompt on the top of the printer. Hit select Print out an auto align pag. Parts for X5150 : 21D0625: AC-Adapter 25W Cartridges : 18L0032 : Black ink cartridge - 600 copies 18L0042 : Color ink cartridge - 450 copies

Error 10 on Xerox Phaser 780

It is a problem with the laser unit. The engine control board did not receive a signal from the laser start-of-scan sensor within the specified time. Solutions : Test the top cover and right front cover switches for proper operation.  Power for the laser unit is routed through both switches. Replace Laser unit - fuser . Replace the engine control board See more about Xerox Phaser 780

Laser printer Xerox Phaser 780

Downloads : Drivers Manuals Cartridges : 016-1678-00 : Toner cartridge Black - 4500 copies 016-1679-00 : Toner cartridge Cyan - 5900 copies 016-1680-00 : Toner cartridge Magenta - 5900 copies 016-1681-00 : Toner cartridge Yellow - 5900 copies 016-1865-00 : Waste toner cartridge - 20000 copies 016-1864-00 : Imaging drum unit - 12500 copies Parts : 2030203: Fuser Unit Troubleshooting : Error 10 Clearing media jams Replacing a waste cartridge Replacing an imaging unit  

How to reset Oki C3400

Solution to reset to the default settings : Enter in "Maintenance Menu" Go to "Execute. If you want to reset the drum counter: The reset is automatic when you insert the new drum. If not: reinstall the drum.

Printer Oki C9600, C9600n, C9600dn

Downloads : Drivers and manuals Cartridges: 42918904: Toner Black C7 42918903 : Toner Cyan C7 42918902 : Toner Magenta C7 42918901 : Toner Yellow C7 42918104 : Image drum Black C7 42918103 : Image drum Cyan C7 42918102 : Image drum Magenta C7 42918101 : Image drum Yellow C7 Parts: 42931701 : Fuser 120V 42931702 : Fuser 230V 42931602 : Transfer Belt 42937601 : Finisher Staples 42869401 : Waste toner collection bottle Troubleshooting: Drum reset: Solution 1: Switch off the power to the printer. Wait approximately five seconds and then flip the power switch back on. Press and hold the "Menu 1/Menu2" button on the control panel and press the "Shut Down/Restart" button to restart the printer. Press the "Menu1/Menu2" button three times in succession until "DRUM CNT RESET" appears on the control panel. Press the "Enter" button to reset the image drum counter on the C9600 printer. Solution 2:

Factory reset for Dell 3000cn, 3010cn, 3100cn

How to clear NVRAM under maintenance : Press Menu. Press down until "Configure" appears, then press right. Press down until "Maintenance" appears, press right. Press down until "Init NVRAM" appears, and press right. "Init NVRAM Are you sure?": press "enter" in the center. Follow instruction and restart the printer (turn off the printer, and then on). How to clear NVRAM under Network Press "Menu". Press down until "Configure" appears, and press right. Press down until "Network" appears, and press right. Press down until "Init NVRAM" appears, and press right. "Init NVRAM Are you sure?": press "enter" in the center. Follow instruction and restart the printer (turn off the printer, and then on). Default username = admin Default password = password

Hp designjet 500 error code 11:11

Solution : You have to connect the trailing cable at two ends. One in the back and one to the printhead.  Before reconnecting, check the ends on the cable as sometimes the connection points get bent or damaged.  If that does not solve your issue: replace the cable ( C7769-60305 or C7770-60274 )

Wast ink counter reset for Epson RX500

Solution : Press and hold all following buttons: Power, Load/Eject, Stop, BW, Color. Release all buttons. After the printer turns on, you'll see "Init eeprom" on printer screen. Press Color button to clear protection counter.

Lexmark X4270: how to fix error 1203

Error 1203 is an issue that occurs either when a cartridge is bad or the printer cartridge Slot is bad... Solution 1 : Try to clean the copper contacts of the both carts and cart slot in the printer and try again.. Solution 2: When error shows up, shut the printers power off; wait one minute and turn it back on press copy. Solution 3 : A 1203 error message on the operator panel could indicate a problem with one of the ink cartridges. Please carry out the steps below the image to confirm that this is a cartridge failure rather than a hardware problem. Make sure the All-In-One is powered on. Pull the control panel towards you, and then open the cartridge access door. The print cartridge carrier moves and stops at the loading position. Pull the old cartridges towards you, and then lift them out. With the cartridges out of the printer, shut the access door and the control panel. Power the printer OFF and then back ON . Check the operator panel to see if the sam

HP Photosmart all-in-one B010, B010a, B010b printers

Downloads : Software & driver Manuals Cartridges : CB316WN : HP 564 Black Ink Cartridge CD994FN : HP 564 Combo Pack Colour Cyan, Magenta, Yellow CB318WN : HP 564 Cyan Ink Cartridge CB319WN : HP 564 Magenta Ink Cartridge CB320WN : HP 564 Jaune Ink Cartridge CN684WN : HP 564XL Black Ink Cartridge CB323WN : HP 564XL Cyan Ink Cartridge CB324WN : HP 564XL Magenta Ink Cartridge CB325WN : HP 564XL Yellow Ink Cartridge Parts : CN643A : Tête d'impression Troubleshooting : Solving error code oxc19a0027 or 0xc19a0027 or 0x6100004c

How to solve error code 5C20 on Canon printers

Solution 1 :  The logic board is faulty: it can't move the rollers and carriage. Try a reset: On the operator panel, press the button. The display will go blank. Unplug the power cord and plug it back in after 30 seconds to ensure that the device resets itself. Then press the button. Once the printer has restarted, try to print a test page Solution 2 : Pump roller sensor error or Error. The pump roller position cannot be detected. Replace Purge drive system unit