Skip to main content

Posts

Showing posts from November, 2011

How to solve error 16H on Konica 2300, 2300DL

Solution : Turn off the printer. Open the panel door exposing the toner waste container and cartridge access area. Gently pry away the waste toner container from the printer.  Put the waste toner powder into a garbage bag. There are two manual screws holding the transfer belt component securely. One is on the left upper part, one is on the right. They are designed to loosen, but stay attached to the transfer belt component. Flip the large blue handle with the arrow upward. Look for a portuding squarish handle below the larger blue handle transfer belt component. Look caredfully at the diagram on this little handle. You must squeeze the level on the underside of this squarish handle to unlock it. Once unlocked you carefully slide this part out. Put this whole component aside for later assembly back in. Carefully slide out the larger transfer belt component about 2/3 of the way out. You should see a pale green plastic handle on the top of this part. You can grab tha

how to reset counter after tranfer belt and fuser replacement on clx2160n

Resetting the transfert belt's counter after replacement ( CLP-300 Imaging Kit ): Solution 1: Press: Menu, #1934, Menu, "Tech Mode " --> OK,  "Data Setup" --> OK, go to "Clear Counts" --> OK, "Enter Password [????]" --> 1934, OK, "Clear Counts [Total Page CNT]", go to "[Imaging Unit]" --> OK, "Clearing…", --> Back. Solution 2 : Enter Service mode by pressing: "menu", "id copy", "left", "right", "menu", "back", "menu" within 5 seconds. Then in data setup clear all memory and clear count Resetting the fuser's counter after replacement (JC96-03609A): Press: Menu, #1934, Menu, "Tech Mode" --> OK, "Data Setup" --> OK, go to "Clear Counts" --> OK, "Enter Password [????]" --> 1934, OK, "Clear Counts [Total Page CNT]", go to "[Fuser

Samsung CLX 3175N, FN, FW Printer

Downloads : Manuals, drivers and software Cartridges : Toner Black CLX-3175   Toner Cyan CLX-3175   Toner Magenta CLX-3175   Toner Yellow CLX-3175 CLT-W409 waste bottle CLX-3175   CLT-R409: Imaging Drum For Samsung CLX-3175   ( Counter reset ) Parts : JC96-05491: Fusing Unit 0604-001095: Photo Interruptor Troubleshooting : Message " replace imaging unit ": You have to change the drum (CLT-R409) Message "System error cycle power": You have to change the photo interruptor.(0604-001095) How to unlock the scanner (message "Scanner locked"): Hold on " Stop " button during 10 seconds. How to replace the fuser unit

Canon Pixma MP530 printer

Download : Manuals Drivers and software Cartridges : Canon CLI-8 3 Pack C/M/Y Value Pack (0621B016) Canon CLI-8 4- Pack C/M/Y/BK Ink Tanks Canon CLI-8 8- Pack C/M/Y/BK Ink Tanks x 2   Canon PGI-5 Pigment Black Ink Tank Parts: QY6-0059 : Printhead Troubleshooting : Error 5B00 ; the waste ink counter need to be resetted: Turn off the printer Hold the Resume Button (red circle in the triangle), add a printer (click “Power”) an indicator light green. Hold the Power Button, release the Resume Button. Not releasing the Power Button, double click “Resume” and release Both Buttons. Click “Resume” for Four times Once you click “Power”, to confirm the selected action (reset counter absorber). To disable the printer “Power” button to click again. Error message U150

How to fix error code 0x61011be5 or ox61011be5 on HP printers

General Printer Error 0x61011be5. Appears on these printers: D7560, C309A, C5390, C6380, ... Genraly it's a carriage jam or a printhead issue. Solution 1 : Do a reset of the printer to factory default settings Verify that the unit is switched on.  Disconnect the  power cable from All-in-One and also from wall outlet. Wait a minute. Plug in the power cable to the printer and also to wall outlet. Unplug the power cable from the printer (with the printer powered on) and wait for 20 seconds. Then, press and hold "#" and "6" while plugging in the power cord. Release the buttons after connect power cord. Solution 2 : Open the printer and wait for the carriage to slide over Remove the ink cartridges from the print head. With a cotton swabs dipped in hot water, clean gently the print head and each ink cartridge, until there is no ink residue coming off on the cotton swab. Once all is dry, replace the cartridges Do a print test. If the er