Skip to main content

Posts

Showing posts from October, 2011

How to fix error B200 on canon Printers

MAJ11/06/17 Error B200 means the printhead voltage or temperature is not normal. The Printhead could be defective.... but first, try these solutions below: Solution 1 : Disconnect the power cable from the printer. Wait 1 hour. Connect the power cable Solution 2 : Check and Clean Head contact pin condition of the carriage unit Check Cable connection especially the carriage FFC Solution 3 : Turn off the power Open the panel Turn on the power Wait for print carriage to start moving to the left. Let it go past half way Before print carriage reaches left hand side shut the cover. Leave the Printer turned on Solution 4 : Unplug the power cable. Open the printer Push the whole print head mechanic to the center While the printer still open, plug the power and turn it ON.  When the printhead still moving and is going to the very LEFT, close the cover.  Wait until its boot up.  Solution 4a: Take out all of the ink cartridges Lift up the gr

Printhead for HP Officejet and Photosmart printers

HP Print Head Printhead CB326-30002 CN642A for HP 564XL and HP 564 : Hewlett-Packard OfficeJet 6000 Hewlett-Packard PhotoSmart B8500 Hewlett-Packard PhotoSmart B8550 Hewlett-Packard PhotoSmart B8553 Hewlett-Packard PhotoSmart B8558 Hewlett-Packard PhotoSmart C5300 Hewlett-Packard PhotoSmart C5324 Hewlett-Packard PhotoSmart C5370 Hewlett-Packard PhotoSmart C5373 Hewlett-Packard PhotoSmart C5380 Hewlett-Packard PhotoSmart C5383 Hewlett-Packard PhotoSmart C5388 Hewlett-Packard PhotoSmart C5390 Hewlett-Packard PhotoSmart C5393 Hewlett-Packard PhotoSmart C6300 Hewlett-Packard PhotoSmart C6324 Hewlett-Packard PhotoSmart C6340 Hewlett-Packard PhotoSmart C6350 Hewlett-Packard PhotoSmart C6375 Hewlett-Packard PhotoSmart C6380 Hewlett-Packard PhotoSmart C6383 Hewlett-Packard PhotoSmart C6388 Hewlett-Packard PhotoSmart D5400 Hewlett-Packard PhotoSmart D5445 Hewlett-Packard PhotoSmart D5460 Hewlett-Packard PhotoSmart D5463 Hewlett-Packard PhotoSmart D5468 Hewlett-P

How to reset Waste ink Counter on Canon Pixma MP480 printer

MAJ 17/10/16 After a message error like " Ink Absorber is Full ", you need to reset the printer to solve the issue: Solution 1 : Search and download the resetter software Power cable and usb cable must be connected Enter in the Service Mode:  1. Turn off the printer without pulling the power cords. 2. Hold down STOP/RESET button and press Power button. 3. Keep holding down Power button and let STOP/RESET button go. 4. Then Press STOP/RESET button twice then let BOTH buttons go. 5. Alternate Blinking error is gone: your are in Service Mode state. Use the Resetter: 1. Extract the resetter software and double click "MP480.exe" W 2. Click Reload Button and you will get a new USB port. 3. Load some papers in your printer and press the "Main" Button once, 4. Wait until the printing is done. 5. Then press "EEPROM Clear" button to clear EEPROM. 6. Then press EEPROM button and the printer will print some text. 7. Then power

How to solve error 5011 on Canon Printers

MAJ 02/01/15 Error 5011 is a scanner error . It occurs on these models: MP480, MP490, MX340, MX320, MX350, MP540, MP620, MP550, MP560, MP600, MP610, MP630, MP800, MP810, MP830, MP970, MP980, MG2100, MG3100, MG4100, MG5100 Solution 1: Unplug power supply Wait 5 minutes Plug back in. Solution 1a (thanks to anonymous): Turn the printer off Open cover as if you want to change an ink cartridge. Turn power on and close cover while initializing   Solution 1b: Power off the printer Press and hold power+cancel simultaneously Hold on the power button and release cancel  Press cancel button 4 times, Release both. Solution 2 : Check for no pieces of paper, no littles objetcs inside the printer. Solution 3 : Carefully clean the encoder strip.  It's located behind the carriage that runs all the way from right to left Solution 4 : Replace the scanner unit

Reset transfert belt counter on Xerox Phaser 6110 MFP

Sometimes, when you have replaced the Image Transfer Belt, the printer still does not work. You will have to reset the counter. Procedure : Enter Service Mode by pressing [MENU] [#] [1] [9] [3] [4] quickly. Select Tech Menu Select DataSetup Arrow to Clear Counts and press Enter Enter Password 1934 Arrow to Transfer Belt and press Enter. The display will show Clearing Counts and then return you to the Tech Menu. Press exit several times to exit the Tech Menu and then power cycle the printer.