Skip to main content

Posts

Showing posts from February, 2010

How to fix "machine error AF" on Brother printers

The scanner flat cable has to be reconnected to the main pcb. - Open the printer scanner cover as you would do to change the carts. - Unlock the blue support and lean the scanner towards a support ("L") open the small cover which will be found in the middle and goes to the left side. - Beneath that is a white flat cable which simply has to be fixed into the main circuitboard (= pcb = printer circuit board).

Printer Canon BJC3000 waste ink tank full

You need to reset waste ink tank counter of your BJC 3000: Turn the power off. While holding down the RESUME button, press and hold the POWER button. The green indicator will light up. While holding down the POWER button, release the RESUME button. Double-click the RESUME button and release the POWER button. (The indicator blinks in orange/green every time the RESUME button is pressed.) When the indicator lights (stops blinking), press the RESUME button three times. Press Power to confirm.

Canon IR1600 error codes

E719 :  The communication between the card reader and the image processor PCB is disrupted. Possible cause The wiring is faulty (short circuit, open circuit). The card reader is faulty. The image processor PCB is faulty. To clear the error in service mode : #12 CLEAR-CARD. Solution: 1) Connector: Is the connection and the wiring for the connector (J1131) of the card reader and the connector (J210) on the image processor PCB normal? 2) Image processor PCB: Try replacing the card reader. If the fault not corrected: replace the image processor PCB. --- E805 After the heat discharge fan drive signal is generated, the fan lock detection signal does not arrive for a specific period of time. Possible cause The fan wiring is faulty (short circuit, open circuit). The heat discharge fan (FM101) is fautly. The DC controller PCB is faulty. Solution: 1) Remove the foreign matter on the fan. 2) Wiring, Connector: Is the connection and wiring of the connector (J951) of the heat discha

Error 1203 on Lexmark P915

Solution : Use a klennex with a few drops of water to dampen and clean off those contact on the holder (do not leave any debris of klennex on those holder contact panel). Before printinganything, run aligned the catridges a couple times then run clean catridges a couple times. Print a test page to see how it's look.

Dell Laserjet 1600 parts list

Parts list for this printer : N5696 110V Engine Power Board Assembly N5796 110V Fuser M5517 ADF Engine Assembly M5914 ADF Lower Cover Assembly M5512 ADF Pickup Assembly 4M346 ADF Rubber Pad K5751 ADF Top Cove G5112 Base Assembly (LOUISIANA, 110V) C5212 Bezel, Prt R5378 Exit Sensor U4718 FAX Terminator Plug, 1600n/ P5150 Front Door Cover N5672 Left Front Cover Support K5684 Left Side Cover N5682 Main Fan (1-wire) AD0624MS-A70GL Main Fan (1-wire) J5946 Main Gear Assembly D5043 Main Paper Output Tray R5080 MODEM, Card R5073 Onal 250-Sheet Paper Tray R5074 OP Panel Controller Board R5075 Op Panel Extension Cover (Paper-Clip Tray) D5035 Op Panel Overlay R5078 Pass-Through Paper Door 7Y600 Power Cord C5210 Primary 250-sheet Paper Tray N5668 Printhead N5640 Rear Cover N5674 Right Front Cover Support J5907 Right Side Cover R5077 Scanning Unit Assembly U5171 Transfer Roller

How to solve ink system failure on HP 3110

Solution 1: - Hold down the "OK", "Cancel", "Black", and "Color" buttons at the same time and turn the printer off. - Keep holding the buttons down until the printer shuts off and turn it back on. - Turn the printer off twice and then it will recalibrate. - Make sure there are new cartridges in the printer so that it can reset. Solution 2: - Remove the cartridges from the product. - Wait for the ' Insert Cartridges ' message to display on the control panel. - Disconnect the power cord from the back of the product. - Wait 60 seconds. - Reconnect the power cord. If the product does not automatically turn on, press the Power button. - Reinsert the cartridges, and then close any open doors on the product. - If you receive a prompt to print a calibration page, do so. - Reconnect the USB cable to the rear of the product, and then try printing again.

Error 0X0000000d with network printer installation

Solution with Windows Vista : Run a command prompt and type the following: net use LPT2: \\servername\printer This sets up a behind-the-scenes connection to the printer. Go through the add printer wizard, choose to add a local printer, and choose port LPT2. Solution with Windows 7 : Go to start and type in " cmd" in the search box.  Right click on cmd and select “ Run as Administrator ”. Type this command net use LPT# \\server\printer /persistent:yes (Substitute #, server, printer as appropriate for your network.) Add your printer locally using the LPT# port. If your laptop has no parallel cable then use LPT1.

Epson Stylus Photo R290 reset

Solution : Download one of these programmes of adjustment here: http://www.printerservice.com.br/public/Adjust_Program_Epson_R290.zip http://rapidshare.com/files/105518320/R290.rar.html Unrar the archive on a folder named "R290" on "C:", then: - Modify the date of the operating system: (01-04-2008). If you run the file LIMPIAR.BAT only verify that changes in the date has been made. - Run the application and select the button "PERSONAL ADJUSTMENT" and select "RESETER INK PAD WASTED"

scanner error. 30.01.19 on HP Laserjet 4100

Inverter PCB or scanning lamp failure. Solutions : - Verify that the scanning lamp briefly illuminates when the printer’s power is turned on. - Verify that the scanning lamp fuse located on the Inverter PCB is not open. - Check for loose connectors and frayed or pinched wires. Reseat the inverter connector at inverter PCB location CN2 and at scanner PCB location J1202. - Replace the scanning lamp with a known functioning lamp. If the problem persists, replace the inverter PCB.