Skip to main content

Posts

Showing posts from December, 2009

How to reset waste ink on Canon MX318

Turn off the printer. Press and hold the RESUME button, then press and hold the POWER (or Stop/reset) button. Still holding the POWER (or Stop/reset) button, Release the RESUME button, Next press and release the RESUME button 2 more times in succession. The printer will enter the"Service Mode". Press the RESUME button 4 times, this will select the clear waste ink counter function. Press the POWER (or Stop/reset) button to "set" the change, and return to the top of the function selection menu. Press the POWER (or Stop/reset) button again to restart the printer.

How to reset ink level for Canon MX300

1. Disconnect the power cable. 2. Connect it while holding down the " power " button 3. With the power button still down, press twice the " Cancel/Stop " red button 4. Release the power button. 5. The printer turns into factory mode: wait for about 10 seconds, then it says " Idle ". 6. Press the ">" (next to the " OK " button) once." Shipping Mode 3 " 7. Press the " OK " button. 8. Press " OK " again for " Without cleaning ". A test page will print.. 9. Open the cover, like you are about to change the cartridges. 10. Disconnect the power cable again. 11. Take out both cartridges. 12. Close the cover. 13. Connect the power cable once again. 14. Turn the printer on. 15. Put the cartridges back.

Error 993 with Lexmark C710

This error code indicates the cam sensor has not bee activated. The sensor activates when the fuser dirve motor turns the cam disk. If the fuser drive motor does not turn on, or the drive parts are not operating: - Check the fuser assembly internal drive gears for binding, or broken or worn teeth. If a problem exists, repair or replace the fuser assembly. Remove the fuser drive motor from the stay assembly, leaving the motor cable connected to the motor. Turn the printer on, but do not allow the motor to touch other areas of the printer. Verify the motor turns during POR. - Check the motor for shorts between the case and each motor winding. If a short is found, replace the motor. - Check the motor for open windings. If found, replace the motor. - Check continuity of the fuser motor/paper feed motor/carriage unit motor cable. If incorrect, replace the cable, if correct, replace the engine board. - Check the fuser drive gears, gears C3-1, C3-2, the clutch spring, motor drive gear, gear C

Canon BJC-8200 error codes

Light Orange - 2 beeps: Remove any paper jammed Light Orange - 3 beeps: Remove any paper jammed Light Orange - 4 beeps: Add Ink Light Orange - 5 beeps: Re-install cartridge or replace it Light Orange - 6 beeps: Re-install cartridge or replace it Light Orange - 7 beeps: Re-install cartridge or replace it Light Orange - 8 beeps: Waste is almost full Flash 1 x Orange - 10 beeps (error code 6100): Try unplugging the printer for 30 seconds, if not requires service. Flash 2 x Orange - 10 beeps (error code 6300): Try unplugging the printer for 30 seconds, if not requires service. Flash 3 x Orange - 10 beeps (error code 6800): Try unplugging the printer for 30 seconds, if not requires service. Flash 4 x Orange - 10 beeps (error code 5100): Make sure nothing is blocking the cartridge movement, if not requires service. Flash 5 x Orange - 10 beeps (error code 5400): Try unplugging the printer for 30 seconds, if not requires service. Flash 6 x Orange - 10 beeps (error code 5B00): Wa

How to reset toner and drum for OKI C8600

Solution : Power on printer while holding both the + & - buttons simultaneously; release when “OKIUSER” is displayed. Press either the + or – button until “ENGINE DIAG MODE” is displayed; press the Enter button and “DIAGNOSTIC MODE xx.xx.xx” will be displayed. Press and hold both the - & On-line buttons simultaneously until “ENG DIAG LEVEL2” is displayed. Press either the + or – button until “CONSUMABLE COUNTER SET” is displayed, press the Enter button; you are now in the menu to set various consumables. Press either the + or – buttons to scroll through the various consumables, at the desired consumable press the Enter button and the last digit of the count will start flashing. Press the Cancel button to decrease the digit amount or press the On-line button to increase the digit amount; press the + or – buttons to move along individual digits in the count. Once the count is at the level you desire, press and hold the On-line, Cancel, & Back buttons simultaneously until the

Error E27 witch Canon Pixma MP198

This error means waste ink counter is full. Solution : 1. Start with printer OFF 2. Hold down RESUME and then hold down POWER 3. Release RESUME 4. press RESUME twice, then release POWER 5. let green light blink until printhead has finished moving. 6. Press resume