Skip to main content

Posts

Showing posts from November, 2009

Error 0xc18a0201 with HP printers

Error code : 0xc18a0201, 0xc18a0206, 0xc18a0306, 0xc18a030a, 0xd0620130, 0x887dd03a, 0xd05d010d, 0xf0af8004, 0xc19ac3ff, 0xc18a050... Solution 1 : Without turning off the product, disconnect the USB cable from the rear of the product. Remove the cartridges from the product. Wait for the ' Insert Cartridges ' message to display on the control panel. Disconnect the power cord from the back of the product. Wait 60 seconds. Reconnect the power cord. If the product does not automatically turn on, press the Power button ( ). Reinsert the cartridges, and then close any open doors on the product. If you receive a prompt to print a calibration page, do so. Reconnect the USB cable to the rear of the product, and then try printing again. Solution 2 : Press and hold the “left arrow” key. Press the “Setup” key and release both keys. Display should say “Enter Special Key Combo” Press and release the “OK” button Then: 1. Press and release

Canon IR1600 error codes

  E000 : The main thermistor reading does not reach 40ºC 14 sec after the fixing heater goes ON. (fixing low temperature error) E001 : The main thermistor reading reaches 220ºC or higher. E002 : A start-up fault is detected under any of the following conditions of the main thermistor E003 : After the end of the WAIT period, the main thermistor reading is 100ºC or lower. In standby, the sub thermistor reading is 50ºC or lower. E004 : At time of initialization, the ZEROXI signal of the power supply is not detected. During temperature control, the ZEROXI signal does not arrive for 3 sec continuously. A short circuit is detected in the triac E010 : A specific revolution is not detected from the main motor rotation detection signal. E100 : When the scanner motor is started up, the BD input signal does not arrive within a specific period of time. When the scanner motor is started up, the motor rotation is too fast, and fails to reach a specific revolution within 20 sec at time of d

10.00.xx errors codes on HP Color Laserjet 5550 series

10.00.00 - The printer cannot read or write to the black print cartridge memory tag. 10.00.01 - The printer cannot read or write to the cyan print cartridge memory tag. 10.00.02 - The printer cannot read or write to the magenta print cartridge memory tag. 10.00.03 - The printer cannot read or write to the yellow print cartridge memory tag. Solution 1 : Turn the printer off and then back on. Solution 2 : If error returns, remove all print cartridges and turn printer off. Turn on and reinstall print cartridges. Solution 3 : Cold reset the printer if error returns Turn the printer on. Watch the control panel. When the memory starts counting, press and hold the green (Select) button. Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady. Release the check button when the Ready, Data, and Attention light are on steady. The control panel will display SELECT LANGUAGE. Press (Down Arrow) button onc

Error 04,041.66 on Xerox C2424

4,0XX.6x Process Control Software Fault Solution 1 : a. Reset NVRAM and then retest. b. Ensure ground integrity for the system. c. Replace the EEPROM chip. d. Reboot the system. 1. From the System Setup menu, go to Information --> Troubleshooting --> Service Tools menu. 2. With the cursor at the top of the Service Tools menu, press both the Up Arrow and Down Arrow buttons to display the Hidden Service menu. 3. Reset NVRAM is in there Solution 2 : 1. Turn the system power ON. 2. Wait for the Xerox logo to begin moving across the display. 3. Before the logo is centered on the display, press and hold the Back and Info buttons on the control panel. 4. Hold both buttons until the display reads “Beginning Service Mode Initialization”. Release the buttons and the system reboots into service mode with the Service Diagnostics menu displayed.

Oki C5400 reset

Re-setting the drum, belt and toners for Oki C5400 . Power on printer while holding both the "+" & "-" buttons simultaneously; release when “OKIUSER” is displayed. Press either the "+" or "–" button until “ENGINE DIAG MODE” is displayed; press "Enter" and “DIAGNOSTIC MODE xx.xx.xx” will be displayed. Press and hold both the "-" & "On-line" buttons simultaneously until “ENG DIAG LEVEL2” is displayed. Press either the "+" or "–" button until “CONSUMABLE COUNTER SET” is displayed, press "Enter" to go in the menu to set various consumables. Press either the "+" or "–" buttons to go to the desired consumable and press "Enter": the last digit of the count will start flashing. Press "Cancel" to decrease the digit amount or press the "On-line" button to increase the digit amount; press the "+" or "–" buttons to move al

How to reset Oki C9300

Procedure : Power ON printer while holding both the "+" and "-" buttons until “ OKIUSER ” message apear in LCD. Press ""+ or "–" button until “ ENGINE DIAG MODE ” is displayed Press " ENTER ", will be displayed " DIAGNOSTIC MODE XX.XX.XX S-MODE " Press "+" or "–" button until “ NV-RAM INITIAL ” is displayed Press " ENTER " again Appear " TABLE 1 " message Press " ENTER " until " EXECUTING RESET " message appears. " NV-RAM INITIAL " message will BLINK... IT resets TONER, DRUM, FUSER and BELT ... Power OFF printer, wait 10 sec, and power ON again To access Service Mode in C9300 : Power ON printer with 0, 1, 6, 7 at same time...

Drum Counter reset for Oki c5300n

a. Press the MENU 1/Menu 2 button while turning the printer on. "USER MNT" appears on the display. b. Press the MENU 1/Menu 2 button until the message corresponding to the color drum you are replacing appears. c. Press the ENTER/POWER SAVE button. RESETTING briefly appears on the display. d. Press the ON LINE button.