Skip to main content

Posts

Showing posts from October, 2009

Xerox Workcentre C2424 Errors

31,004.40:6909 : it's a mechanical initialization jam error. Pull out the paper tray to make sure it doesn't have a jam. Try also to manually feed some heavy paper or card stock through the printer to make sure the sensor in the preheater isn't stuck. 39,002.40 : DRAM test failure. 39,012.40:56208 : "Cycle the power" and if that does not work replace the document feeder. 39,012.41 : Document Feeder Optical Failure. Replace the document feeder. 4,0XX.6x: Process Control Software Fault. Reset NVRAM and then retest. Ensure ground integrity for the system Replace the EEPROM chip. Reboot the system. From the System Setup menu, go to "Information", "Troubleshooting" Service Tools menu. With the cursor at the top of the Service Tools menu, press both the Up Arrow and Down Arrow buttons to display the Hidden Service menu. Reset NVRAM is in there.

Canon SmartBase MPC400 errors code

##332 [ TX / RX ] Printer control DRAM check error. It could be a printer control DRAM malfunction: power cycle the machine or replace the board containing a printer control DRAM. SCNT PWB malfunction: power cycle the machine or replace the SCNT PWB. ##333 [ TX / RX ] Printer control ROM check error. Printer control ROM malfunction: power cycle the machine or replace the board containing a printer control ROM. SCNT PWB malfunction: power cycle the machine or replace the SCNT PWB. ##334 [ TX / RX ] Printer control EEPROM check error. The printer control EEPROM is damaged: power cycle the machine. Check the ink capacity of the ink suction unit waste ink tank, and input the waste ink capacity value corresponding to the amount of absorbed ink. Printer control EEPROM malfunction: SCNT PWB malfunction. Power cycle the machine or replace the SCNT PWB. ##335 [ TX / RX ] Data communication error between system Control section and Printer contro

Error "X cartridge not installed" with Konica Minolta 2400/2500 series

Information is relevant for the printers Konica Minolta Magicolor 2400W, 2430 DL, 2450, 2480MF, 2490MF, 2500W, 2530DL, 2550EN, 2580MF, 2590MF. Solution : Gently clean any toner dust from the small microchip on each cartridge Gently clean any toner dust from the 3 copper sensor prongs on the chip sensor (inside the printer) The sensor is very easy to damage. If cleaning the sensor does not work we would suggest contacting Konica Minolta for a replacement part.

Brother MFC-9420CN error list

Error list: 20 - Laser power error 21 - Beam detector error 22 - Nvram error 23 - Engine controller error 24 - Process timing clock error 25 - Developing motor error 26 - Main motor error 27 - Scanner motor error 28 - Charge HV unit error 29 - LVPS error 2A - Fuser thermistor error 2B - Fuser heater error 2C - Fuser temperature low error 2D - Fuser temperature low error 2E - Fuser temperature high error 2F - Fuser ACOFF error 30 - Erase LED error 31 - Power supply fan error 32 - Exit fan error 33 - Laser unit fan error 34 - Yellow switching clutch error 35 - Magenta switching clutch error 36 - Cyan switching clutch error 37 - Black switching solenoid error 38 - Yellow switching solenoid error 39 - Magenta switching solenoid error 3A - Cyan switching solenoid error 3B - Black switching solenoid error 3C - Transfer belt error 3D - Transfer roller solenoid error 3E - Transfer roller solenoid error 3F - Fuser unit clutch error 40 - Belt marker sensor error 41 - HVU connection error 42 - To