Skip to main content

Posts

Showing posts from April, 2009

Error 79 on HP Laserjet

MAJ 17/10/16  If you have error 79 on your HP laserjet, try this solution: Unplug Hold down "*" & "enter/ menu buttons" While holding down both buttons, turn power on Wait until something like "initialize" shows up on the display Let go of buttons Wait until display reads "ready" Unplug for 10 seconds, then plug back in

Waste ink tank reset for Canon MP190

MAJ 17/10/16 Here is the procedure to reset the waste ink counter on Canon Pixma MP190 . 1) Enter service mode by pressing: MENU, COPY, SCAN, COPY, COPY 2) Select TEST MODE 3) Select (8) PRINTER TEST in TEST MODE 4) Select (3) (eeprom clear) 5) Select (0) (ink count) 6) Press the SET key 7) Press the STOP/RESET key, then press power key to power off

Message "ink pads are full" on Epson C45

MAJ 17/10/16 If you have the error message " ink pads are full ", you need to reset the waste ink pad. Here is the solution: Step 1 : Download Scc utility Step 2 : SSC Service Utility allow you to do many amazing things with Your Epson printer : 1) Work directly with CSIC in Epson Stylus printers cartridges. 2) Reset or rewrite any chip using special addon device. 3) Freeze internal ink counters. 4) Reset internal ink counters even with empty cartridges. 5) Separate cleaning of color and black heads for all Epson inkjet printers, powerful cleaning mode. 6) Hot swapping of cartridges supported. 7) Resetting of protection counter (even then it is already full).

Ink counter reset on Canon Pixma MP110

MAJ 17/10/16 If you have the error code 5800 or 5b00 , you need to reset the waste ink counter. Reset procedure : Enter SERVICE MODE By pressing Menu-Scan-Copy-Scan Enter NVRAM by presing <--- or ---> then OK Enter CMY ink level by pressing <--- or ---> then OK Select 1 by presing <--- or ---> then OK Enter K ink level by presing ---> then OK select 1 by presing <--- or ---> then OK Press reset ( design: // )

How to fix error code 0xf0af8004 on HP printers Officejet 5510

  MAJ 27/06/16 Try this procedure to solve error code 0xf0af8004 : Solution : Without turning off the product, disconnect the USB cable from the rear of the product. Remove the cartridges from the product. Wait for the ' Insert Cartridges ' message to display on the control panel. Disconnect the power cord from the back of the product. Wait 60 seconds. Reconnect the power cord. If the product does not automatically turn on, press the Power button. Reinsert the cartridges, and then close any open doors on the product. If you receive a prompt to print a calibration page, do so. Reconnect the USB cable to the rear of the product, and then try printing again. If you have completed all the steps listed above and are still experiencing a problem, service the product.

Waste ink reset for Canon SmartBase MP360, MP390

 MAJ 27/06/16 Here is the procedure if you need to reset waste ink counter on Canon SmartBase MP360 and MP390: Printer on, press Additional Functions, Scan , Copy , Scan . Now you should be in service mode. Select Test mode. Select #8 Printer Test, push the + or - button until it says 8-3 then hit the select button. The menu will say EEPRON Clear Select Ink count which is option (0) and press set Then press Stop/Reset Followed by the power button and then wait for it to restart.

How to solve error code 0XC18A0406 on HP printers

  MAJ 27/06/16 The error code 0XC18A0406 could appears ont these HP printers: Photosmart 3210, C5180, C7280... Try this : Press the On button to turn the printer off. Unplug the power cord from the back of the printer. Remove all the ink cartridges. Wait two minutes. Plug the power cord into the back of the printer. Press the On button to turn the printer on. Install the ink cartridges when prompted. If the error code does not display, the issue is resolved. If the 0xc18xxxxx or 0xc19xxxxx ink system error code displays on the front panel, service the printer.

Hard Factory Reset on Lexmark T522

MAJ 13/11/15 Here is the procedure to make a hard factory reset on Lexmark T522 : Boot the printer into the config menu by holding " Select " and " Return " (buttons 3 and 4) while powering on the printer. Then scroll across to the " Operator menu " and select " Enable ". Then scroll to " Exit menu " and select. this will unlock the op panel menus but will not remove any passwords. To remove the password: enter the network se menu through the standard operator panel menu: Scroll to the network menu press select Scroll to standard network setup (network 1 setup if you have a optional network card as opposed to the one intergrated into the rip). Scroll to print(do not press select on this option) Press and hold the "Go" button while doing this press and release the left menu button. This brings the printer into the network SE menu scroll to the nvram option and select then scroll to reinit nvram and select.

Error "unable to clean" on Brother MFC

  MAJ 13/11/15 Here is the procedure to solve error message " unable to clean " on Brother inkjet printers: Solution : Machine off Switch on the machine while holding down the “menu”button until all the leds are flashing on/off. Now you are in “maintenance” mode. Press 80 Press the “mono start” button several times until you see “purge: xxxx” Press “2783” in order to reset the purge counter. You will see: “purge:0000” Press the "stop" button. Press “99” to exit the maintenance mode. See also: Error 46 on Brother printers If you want to replace the absorber box: LF7443001: Ink Absorber Weld Assy

Waste ink reset for Canon I850

MAJ 13/11/15 Here is the procedure to reset waste ink counter on Canon I850 :     Start with the printer OFF 1. Hold down RESUME and then hold down POWER 2. Release RESUME 3. Press RESUME twice, then release POWER 4. Let green light blink until printer is done futzing Select function with RESUME press POWER to execute: presses - light color - function 0 - green - Pressing power button will turn off printer 1 - orange - Service Test Print 2 - green - EEPROM Information Print 3 - orange - Initialize EEprom data 4 - green - Reset Waste ink Counter 5 - orange - Mode to set Destination code (1: Overseas, 2: Domestic) 6 - green - Refresh printhead (cleaning mode) Parts : Canon Printhead QY6-0064 for i560, iP3000, i850, MP700, MP730 Printers

System Error 08:11 on HP Designjet 500 and 800 series

MAJ 13/11/15 Here is the procedure to solve the error 08:11 on HP Designjet 500 and 800 printers: First, verify the printer's current Firmware release and upgrade as needed. Turn the printer off then on and attempt to recreate the error message. If no error appears, attempt to verify functionality. If the error re-appears, continue with the remaining steps. Turn the printer off and disconnect the data cables (parallel and/or network), leaving the power cable connected. Turn the printer on, if the error re-appears continue with the remaining steps. If no error, verify functionality as instructed below (troubleshoot data cables, file(s), computer port type, etc). Check all the connections on the Interconnect PCA and Electronics module (refer to pg. 8-7, 8-8 of the 500/800 Series Service Manual ). If problems noticed and corrected, attempt to verify functionality before continuing with the remaining steps. WARNING: To prevent p

Error 49.FF81 on HP 4100mfp and 9000mfp series

 MAJ 02/09/15 For solving error code 49.FF81 , verify printer functionality: Power off the MFP and remove the EIO hard disk. To remove the hard disk remove the two screws from the EIO1 or EIO2 slot on the back of the MFP (depending on which slot the hard drive is installed in). Power up the MFP (turn it on), it will boot up with the message " HARD DISK NOT INSTALLED, COPY AND SEND DISABLED." Print a Configuration Page by performing the following: Press the Menu key until Information is shown on the display, then press the Select key to highlight the Information Menu. Highlight Print Configuration and press the Select key. The MFP should print out two pages. Test the MFP by send several print jobs over the network to the MFP from a PC. If the MFP prints the test print jobs successfully, power down the MFP and reinstall the hard drive. Proceed to the next section and perform a Disk Init. If the MFP fails to successfully print any of these te

79.00FE error code on HP laserjet 4050/N/TN

 MAJ 02/09/15 A cold reset may be the solution for error code 79.00FE: - Print a configuration page (if you can) - Remove the Jet Direct and power on while holding the 'GO' button down. After display reads OFFLINE, the reset is complete. After the cold reset, remove the jetdirect card (with the printer off), and see if the 79 error goes away. If the error appears before a job is sent then it may be the DIMMS, try removing them to see if the error persists. If that doesnt work try swapping the formatter PCA with another from a known good printer.

HP Photosmart D7160, C5180: Error: 0xc19a0024, oxc19a0024

MAJ 02/09/15 Here are some solutions for errors code 0xc19a0024 and oxc19a0024   Solution 1: Turn off power and unplug from power source. Open right side of printer. Disconnect,by pulling gently, both white flat ribbon cables off the main circuit board. Plug in power source and turn printer on. Wait till you get a error message and push " Ok ". Unplug power source. Reconnect the flat ribbon cables by aligning and carefully pushing into the conectors on the main circuit board. Plug in power source and turn printer on. Solution 2: Turn off power and unplug from power source. Open right side of printer (looking at the front). Disconect,by pulling gently, the flat ribbon cable off the main circuit board that is the smaller of the two. Plug in power source and turn printer on. Wait till you hear no more movement from inside from unit booting up. Press both cancel and power button at the same time. Message on printer screen will be, " Enter S